Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Modelling Internal Combustion Engines with Dynamic Staggered Mesh Refinement

Effect of Piston Crevices on 3D Simulation of a Heavy-Duty Diesel Engine Retrofitted to Natural Gas Spark Ignition

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Multidimensional Computational Fluid Dynamics Combustion Process Modeling of a 6V150 Diesel Engine

An Advanced High Dimensional Model Representation Approach for Internal Combustion Engine Modeling and Optimization

Three-Dimensional Computational Fluid Dynamics Modeling of a 6V150 Diesel Engine

Multidimensional Numerical Modeling of Combustion Dynamics in a Non-Premixed Rotating Detonation Engine With Adaptive Mesh Refinement

Numerical Simulation of HCCI Engine with Multi-Stage Gasoline Direct Injection Using 3D-CFD with Detailed Chemistry

A Transport Equation Residual Model Incorporating Refined G-Equation and Detailed Chemical Kinetics Combustion Models

Numerical Simulation of Gasoline Stratified Charge Compression Ignition Using 3D-CFD Coupled with Detailed Chemistry

Realistic fuel spray modeling for gasoline direct injection engine applications

Combustion model development of future DI engines for carbon emission reduction

MULTI-DIMENSIONAL MODELING OF THE CFR ENGINE FOR THE INVESTIGATION OF SI NATURAL GAS COMBUSTION AND CONTROLLED END-GAS AUTOIGNITION

Application of the Optimized Decoupling Methodology for the Construction of a Skeletal Primary Reference Fuel Mechanism Focusing on Engine-Relevant Conditions

Simulating low temperature diesel combustion with improved spray models

Toward Efficient Chemistry Calculations in Engine Simulations Through Static Adaptive Acceleration

Experimental Investigation and Numerical Modeling of Spray Combustion and Emission in a Diesel Engine

Mass-Flux-Based Implicit Multigrid Method for Modeling Multidimensional Combustion

Modeling Heavy-Duty Diesel Engines Using Tabulated Kinetics In A Wide Range Of Operating Conditions

LARGE EDDY SIMULATION FOR INTERNAL COMBUSTION ENGINES: PROGRESS AND PROSPECTS

Multi-dimensional simulation of HCCI engine using parallel computation and chemical kinetics