Abstract:Crystallinity (Xc) is a crucial crystallographic factor that related closely to mechanical properties in linear polyethylene or high density polyethylene (HDPE), whose molecular weight (MW) is at a 105 level. However, as a typically intractable-processing polymer, the structure-property relationship concerned Xc is still ambiguous for ultrahigh molecular weight polyethylene (UHMWPE) with MW﹥1.5×106. The reason is that high entanglement density hinders chain mobility in the course of UHMWPE crystallization, thus crystalline degree in UHMWPE molding parts is difficult to be artificially modulated within a wide scope. In this study, low chain-entanglement status of UHMWPE melt was achieved by (1) utilizing lowly entangled nascent UHMWPE synthesized via the single-site Ziegler-Natta catalyst, and (2) decreasing the sintered temperature. It is impressive that partial disentanglement reserved in the melt is favorable for obtaining higher crystallinity. Meanwhile, an isothermal crystallization treatment was additionally adopted to further improve the capacity of regulating crystallization after the traditional two-step sintering procedure. By a combination of varying the initial entanglement in nascent powders, sintering temperature, isothermal crystallization duration, and molecular weight of UHMWPE, the Xc of the compression-sintered products has been successfully adjusted in the relatively broad range of 29%≦ Xc≦65%, which offered an opportunity to validly survey the correlation between mechanical property and crystallinity. Particular attention was paid to the yield strength. A linear master straight-line can be plotted as yield strength vs. Xc for all of the samples inspected, indicating crystallinity also plays a dominant role on mechanical performances of UHMWPE sintering parts, as same in the case of HDPE. However, the mechanical reinforcement induced by increment of Xc in UHMWPE is more efficient than in HDPE. The yield strength of UHMWPE is much higher than that of HDPE at the same Xc, indicating the amorphous phase or entanglements in UHMWPE is crucial to determine the mechanical property. These findings are of significance for guiding the manufacturing of high-performance UHMWPE materials via crystallization manipulation.

Crystal Morphology and Corresponding Physical Properties of Nascent Ultra-High Molecular Weight Polyethylene Powder with Short-Branched Chains

Phase Structures of Nascent Polyethylene Powder Studied by Wideline Proton Nmr

Studies On The Nature Of The Macromolecular Condensed State Of "Nascent" Ultra High Molar Mass Polyethylene

Nascent particle sizes and degrees of entanglement are responsible for the significant differences in impact strength of ultrahigh molecular weight polyethylene

Chain Entanglement Regulation of Sintered Ultrahigh Molecular Weight Polyethylene and Its Effect on Properties

Morphology and Plastic Yielding of Ultrahigh Molecular Weight Polyethylene

Nanometer Scale Mechanical Study on Well Defined Nanostructured Chain Aggregation of Polyethylene

Pursuit of the correlation between yield strength and crystallinity in sintering-molded UHMWPE

Role of the Amorphous Morphology in Physical Properties of Ultra High Molecular Weight Polyethylene

Melt Processing and Structural Manipulation of Highly Linear Disentangled Ultrahigh Molecular Weight Polyethylene

Effect of small amount of ultra high molecular weight component on the crystallization behaviors of bimodal high density polyethylene

Melting Behavior and Morphology of Freeze-Dried Ultra-High Molar Mass Polyethylene

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Effects of Different Ultrahigh Molecular Weight Polyethylene Contents on the Formation and Evolution of Hierarchical Crystal Structure of High‐density Polyethylene/ultrahigh Molecular Weight Polyethylene Blend Fibers

Exploring the Entangled State and Molecular Weight Ofuhmwpeon the Microstructure and Mechanical Properties Ofhdpe/uhmwpeblends

Structure and Properties of Gel‐spun Ultra‐high Molecular Weight Polyethylene Fibers Obtained from Industrial Production Line

13C Solid State NMR Characterization of Structure and Orientation Development in the Narrow and Broad Molar Mass Disentangled UHMWPE

The Isothermal Melting Kinetics of Ultrahigh Molecular Weight Polyethylene Crystals

Eminent differences in cryogenic toughness of ultra‐high molecular weight polyethylene with different entanglement densities

Functionalized phenoxy-imine catalyst for synthesizing highly crystalline nascent UHMWPEs: 2: The non-isothermal crystallization kinetics towards the nascent less entangled UHMWPEs

Improved Crystallizability and Processability of Ultra High Molecular Weight Polyethylene Modified by Poly(amido Amine) Dendrimers