Abstract:Recently, sodium ion batteries (NIBs) gained increasing attention, because of its abundant reserves and relatively even geological distribution. However, the development of NIBs is greatly hampered because of the lack of appropriate active materials for both cathodes and anodes. Since the Na ion is ca. 55% larger than the Li ion, finding suitable host materials with sufficiently large interstitial space to accommodate sodium ions and to allow reversible and rapid ion insertion and extraction is very difficult. NASICON-type Na3V2(PO4)3 has recently been considered as a prospective cathode material for NIBs, because of its highly covalent 3D framework crystalline structure, high energy density (~400 Wh/kg) and good thermal stability. For anode materials, disordered carbon is particularly attractive because of their large interlayer distance and disordered structure that could accommodate sodium ions. Here, we briefly present porous carbon based electrodes for NIBs with excellent rate performance: (1) Carbon-coated nanosized Na3V2(PO4)3 embedded in the porous carbon matrix (abbreviated as CC-NVP@PCM); (2) Nitrogen-doped activated porous carbon fibers (ACFs); (3)Flexible free-standing porous carbon nanofibers (P-CNFs) with three-dimensional (3D) interconnected structure. The CC-NVP@PCM was prepared by using a facile soft-chemistry based method with post heat-treatment. It shows high rate performance (44 mAhg-1at 200C ). This ultrahigh rate performance is comparable to that of supercapacitor, but with much higher energy density. The ACFs were synthesized by pyrolysis of Ppy nanofiber precursor. It shows excellent capacity retention and extraordinary rate performance. The reversible capacity at 0.05 Ag-1 is 296 mAhg-1 and could still maintain as 72 mAg-1 at a current of 10 Ag-1. In case of the P-CNFs electrode prepared by electrospinning, it delivers a reversible capacity of 266 mAh.g-1 after 100 cycles at 0.2C, corresponding to 80.3 % of the initial charge capacity. When cycled at a current density as high as 500 mAg-1 (2C), it still delivers a reversible capacity of ~140 mAh.g-1after 1000 cycles. The improvement of electrochemical performance of these porous carbon based electrodes for NIBs is attributed to the special design and porous structure, which confined a variety of advantages: hierarchical porous channels enabling short transport length for ions and electrons, carbon coated structure resulting in low resistances, good mechanical properties leading to the excellent morphology stability.

High nitrogen doped carbon nanofiber aerogels for sodium ion batteries: synergy of vacancy defects to boost sodium ion storage

Engineering Capacitive Contribution in Nitrogen-Doped Carbon Nanofiber Films Enabling High Performance Sodium Storage

Nitrogen and sulfur co-doped mesoporous hollow carbon spheres for high rate sodium ion storage

Sulfur-/Nitrogen-Rich Albumen Derived "Self-Doping" Graphene for Sodium-Ion Storage.

F and Si Dual-Doping Induced Oxygen Vacancies in a Na4Fe3(PO4)2P2O7 Cathode Enables Boosting Electrochemical Performance for Sodium Storage

Sodium storage behavior and long cycle stability of boron-doped carbon nanofibers for sodium-ion battery anodes

A Flexible Sulfur-Enriched Nitrogen Doped Multichannel Hollow Carbon Nanofibers Film for High Performance Sodium Storage.

Regulating the Sodium Storage Sites in Nitrogen-Doped Carbon Materials by Sulfur-Doping Engineering for Sodium Ion Batteries

Double-shell and hierarchical porous nitrogen-doped carbon nanocages as superior anode material for advanced sodium-ion batteries

Enhancing capacitive storage of carbonaceous anode by surface doping and structural modulation for high-performance sodium-ion battery

A densely packed Sb 2 O 3 nanosheet-graphene aerogel toward advanced sodium-ion batteries.

Sb/N‐Doped Carbon Nanofiber as a Sodium‐Ion Battery Anode

Electrodes for Sodium-Ion Batteries with Excellent Rate Performance Using Porous Carbon Networks

Mussel-inspired nitrogen-doped porous carbon as anode materials for sodium ion batteries

Nitrogen and sulfur co-doped mesoporous carbon derived from ionic liquid as high-performance anode material for sodium ion batteries

Codoped Holey Graphene Aerogel by Selective Etching for High-Performance Sodium-Ion Storage

Interlayer-expanded MoS2 nanosheets/nitrogen-doped carbon as a high-performance anode for sodium-ion batteries

SnS/SnSb@C Nanofibers with Enhanced Cycling Stability Via Vulcanization As an Anode for Sodium‐Ion Batteries

Integrating Nanoreactor with O–Nb–C Heterointerface Design and Defects Engineering Toward High‐Efficiency and Longevous Sodium Ion Battery

Constructing nitrogen-doped porous carbon immobilized Co9S8 composite as high-performance anode material for sodium-ion batteries

Hybrid-Mechanism Synergistic Flexible Nb2O5@WS2@C Carbon Nanofiber Anode for Superior Sodium Storage