Abstract:Doubly fed induction generators (DFIGs) are negatively affected by the inter-turn short-circuit fault of rotor windings, so for continuous and safe operation of the wind turbine, it is important to examine the DFIGs. For this purpose, a finite element method (FEM) based model has been designed to check the behavior of the generator under normal and inter turn short circuit fault condition in the rotor windings. In this paper, a fieldcircuit coupled model of machine was designed using ANSYS Maxwell 2D. The circuit is modeled by a small elements mesh. Three phase AC current source is provided to the rotor windings and the excitations on rotor winding side are set in the external circuit. The stator and rotor slot number are 72/60 and number of turns per phase for stator and rotor are 228/100. The outer diameter of stator is 520mm and the inner diameter is 350mm. The outer diameter of rotor is 346.6mm and the inner diameter is 110mm. Different rotor inter turn short circuit fault conditions are accomplished by reducing the number of turns in rotor slot. Based on the simulation, it was found that phase difference and positive and negative sequence of current analysis were effective methods to diagnosis the rotor inter turn short circuit fault. During the normal operation, all the three phases are equally distributed and are 120° degrees apart and start to distracted from 120° degree when inter turn short circuit happened. Under normal condition, the negative sequence of current is low. However, as the fault degree enlarges, negative sequence of current becomes larger, thus ratio of negative to positive sequence of current also increases. The simulation results illustrate that the analysis done in this paper is quite appropriate as desired, also proposed technique is advanced in wind turbines.

On Shortening the Numerical Transient in Time-Stepping Finite Element Analysis of Induction Motor under Inter-Turn Short Circuit Fault Faults

Modeling and Evaluation of Stator and Rotor Faults for Induction Motors

Loss Investigation for Multiphase Induction Machine under Open-Circuit Fault Using Field–Circuit Coupling Finite Element Method

Fast Steady-State Analysis in Time-Stepping Finite-Element Simulation of Induction Motors Based on Virtual Blocked Rotor Techniques

Diagnostic Method of Induction Motor Stator Winding Interturn Short Circuit Fault Based on the Feature Impedance

Inter-turn Fault Detection for the Inverter-Fed Induction Motor Based on the Teager-Kaiser Energy Operation of Switching Voltage Harmonics

Analysis of Inter-Turn Short-Circuit Faults in Brushless DC Motors Based on Magnetic Leakage Flux and Back Propagation Neural Network

Rotor Faults Diagnosis for Induction Motors Considering Effects of the Load and Inertia

Stator inter-turn fault detection for the converter-fed induction motor based on the adjacent-current phase-shift

Fault Tolerant Control of Harmonic Injected Nine-Phase Flux Switching Permanent Magnet Motor Drive System

Numerical Modeling, Electrical Characteristics Analysis and Experimental Validation of Severe Inter-Turn Short Circuit Fault Conditions on Stator Winding in DFIG of Wind Turbines

Simulation and Analysis of Squirrel Cage Induction Machines under Rotor Internal Faults

A Comprehensive Analysis of Short-Circuit Current Behavior in PMSM Interturn Short-Circuit Faults

Online Identification Methodology of Field Winding Short Circuit Fault of Turbogenerator

Harmonic Model and Remedy Strategy of Multiphase PM Motor under Open-Circuit Fault

Detection of Stator Winding Faults in PMSMs Based on Second Harmonics of Phase Instantaneous Reactive Powers

Rotor Faults Diagnosis in Rotor Field Oriented Controlled Induction Motors Based on Torque Current

Quantitative Broken Rotor Bar Fault Detection for Closed-Loop Controlled Induction Motors

Simulation Using Matlab/Simulink On Rotor Winding Inter-Turn Short Circuit Fault In Dfig

Interturn Short-Circuit Faults in Permanent Magnet Synchronous Machines: an Extended Review and Comprehensive Analysis

Detection of Rotor Inter-turn Short Circuit Fault in Doubly-fed Induction Generator Using FEM Simulation