Abstract:A new strategy; cation and anion dual gradient, is proposed and successfully constructed at the surface of LiCoO2 to minimize the highly oxidized Co4+ and O− species when charged to high potentials, which not only suppresses the relevant surface side reactions, but also affected the Li+ diffusion kinetics through the induced spinel‐like surface structure, making LiCoO2 exhibit excellent cycling stability and rate capability at the high cutoff voltage of 4.6 V, further validated in the 4.55 V pouch full cell (equivalent to 4.6 V vs Li/Li+).LiCoO2 (LCO) is the most successful cathode material for commercial lithium‐ion batteries. Cycling LCO to high potentials up to 4.5 V or even 4.6 V can significantly elevate the capacity but cause structural degradation due to the serious surface side reaction between the highly oxidized Co4+ and O− species with organic electrolytes. To tackle this concern, a new strategy, constructing cation and anion dual gradients at the surface of LCO (DG‐LCO), is proposed. Specifically, the electrochemically inactive cation and anion are selected to substitute Co3+ and O2− at the surface in a gradated manner, thus minimizing the highly oxidized Co4+ and O− species at high potentials and suppressing the induced surface side reactions. Unexpectedly, this dual gradient design leads to a spinel‐like surface structure coherently with bulk layered structure, which facilitates Li+ diffusion kinetics. Thus, DG‐LCO achieves high capacity and excellent cycling stability at 4.6 V (≈216 mA h g−1 at 0.1 C, a capacity retention of 88.6% after 100 cycles in 1.8 A h pouch full cell at 1 C), as well as improved rate capability (≈140 mA h g−1 at 5 C). These studies provide useful guidelines for future design of cathode materials with long lifespan and high rate capability.

Reversible Phase Transition Enabled by Binary Ba and Ti-based Surface Modification for High Voltage LiCoO2 Cathode

Off-Stoichiometry Induced Few-Nanometer Surface Layer for High-Performance Layered Cathode in Nonaqueous and Aqueous Electrolytes

Enhancing the Reversibility of Lithium Cobalt Oxide Phase Transition in Thick Electrode via Low Tortuosity Design

A Surface Modification Layer with Cobalt Aluminate Inhibits 4.6 V High-Voltage Phase Transition of LiCoO2

A surface modification layer with cobalt aluminate inhibits 4.6 V high-voltage phase transition of LiCoO 2

Electrochemically Driven Phase Transition in LiCoO2 Cathode

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO 2

Structure/Interface Coupling Effect for High‐Voltage LiCoO2 Cathodes

In-Situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO 2 Cathode at High-Voltage

A new surface phase of Al2Ti7O15 to enhance the electronic conductivity and interfacial stability of LiCoO2 cathode materials

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO2

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO<sub>2</sub> at 4.65 V

Surface Design with Cation and Anion Dual Gradient Stabilizes High-Voltage LiCoO<sub>2</sub>

Improving diffusion kinetics and phase stability of LiCoO2 via surface modification at elevated voltage

In-situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO2 Cathode at High-Voltage

Improving Stability of High Voltage LiCoO2 by Synergetic Surface Modification Via in Situ Surface Conversion

Structure/Interface Coupling Effect for High‐Voltage LiCoO<sub>2</sub> Cathodes

High‐Entropy Surface Complex Stabilized LiCoO2 Cathode

Double function-layers construction strategy promotes the cycling stability of LiCoO2 under high temperature and high voltage

Structure/Interface Coupling Effect for High‐Voltage LiCoO2 Cathode

A multifunctional manipulation to stabilize oxygen redox and phase transition in 4.6 V high-voltage LiCoO2 with sXAS and EPR studies