Abstract:In order to promote the application of LIBS technology in electrolytic aluminum industry, give full play to its advantages of rapidness, no preparation and multi-element simultaneous detection. The contents of Fe and Si elements in general aluminium procuced from electrolysis process were detected by means of laser induced breakdown for the first time, and the reasonable experimental conditions were explored, the calibration curves were established and the content of Fe and Si in general aluminium were quantitatively analyzed based on reasonable experimental conditions. The accuracy of LIBS measurement results were examined according to national standard GB / T 7999-2015 "optical emission spectrometric analysis method of aluminum and aluminum alloy". The fundamental frequency 1 064 nm laser produced by Nd : YAG pulsed laser device as the excitation source producing plasma, the spectral informations were detected and recorded by multi-channel grating spectrometer and ICCD detector. First of all, LIBS spectral line was detected and the spectral line was assigned, the line of Al I 266. 04 nm, Si I 288. 15 nm and Fe I 259. 92 nm were selected for quantitative analysis through comprehensive consideration. The influence of trigger delay time, 1Q delay time, laser setting voltage on the spectral signal intensity and SNR were researched respectively in the paper. The experimental results show that the trigger delay time of 4 mu s, 1Q delay time of 170 similar to 190 is, the laser set voltage of 560 V are the reasonable experimental parameters for Si and Fe element quantitative analysis in this paper. According to the relationship between spectral intensity and elemental concentration, the calibration curves were cestablished by the internal standard method. The correlation coefficients were 0. 952 11 and 0. 919 72, and the relative standard deviation were 6. 34% and 7. 25% for Fe and Si elements respectively. There was a good linear relationship between concentration and spectral intensity, and the 12 samples were quantitatively analyzed base on the above model. The relative error of Fe content is 0 similar to 17. 3% and the relative error of Si content is 0 similar to 14. 3% compared with the results obtained by OES. The measurement results 100% comply with the allowable requirements for Si content in 12 samples, and the results 91. 7% meet the allowable difference requirements according to national atandard GB/T 7999-2015 "optical emission spectrometric analysis method of aluminum and aluminum alloy". The experimental results show that, LIBS technology has a certain value of promotion and using in the electrolytic aluminum industry for Fe and Si elements detection.

A Gaussian Spot Overlap Ablation Model for Prediction of Aluminium Alloy Spectral Peak Intensity in High Pulse Repetition Frequency LIBS

A Strategy to Reduce Spectral Intensity Uncertainty and Predicted Content Uncertainty of Low and Medium Alloy Steel Elements

Automatic background correction method for laser-induced breakdown spectroscopy

Stability and Accuracy Improvement of Element Analysis in Steel Alloys Using Polarization-Resolved Laser-Induced Breakdown Spectroscopy

A Plasma Image-Spectrum Fusion Correction Strategy for Improving Spectral Stability Based on Radiation Model in Laser Induced Breakdown Spectroscopy.

A Spectrum Standardization Approach for Laser-Induced Breakdown Spectroscopy Measurements

Optical Scanning Analysis of Static Samples by Compact Laser Induced Breakdown Spectroscopy

A Method for Improving the Accuracy of Calibration-Free Laser-Induced Breakdown Spectroscopy by Exploiting Self-Absorption.

Three-dimensional Elemental Imaging of Material Surface Using Image-Assisted Laser-Induced Breakdown Spectroscopy

Design and optimization of handheld alloy analysis instrument based on microjoule high pulse repetition frequency LIBS

Quantitative Analysis method of laser-induced breakdown spectroscopy based on temperature iterative correction of self-absorption effect

An Efficient Procedure in Quantitative Analysis Using Laser-Induced Breakdown Spectroscopy

An Echellograms-Based Quantitative Analysis Method of Laser-Induced Breakdown Spectroscopy

A Partial Least Squares Based Spectrum Normalization Method for Uncertainty Reduction for Laser-Induced Breakdown Spectroscopy Measurements

Performance investigation of pre-ablation and reheating orthogonal double-pulse nanoparticle enhanced laser-induced breakdown spectroscopy

Investigation on Experimental Conditions and Quantitative Analysis for Fe and Si Elements in General Aluminum by Laser Induced Breakdown Spectroscopy Technique

A Calibration-Free Model for Laser-Induced Breakdown Spectroscopy Using Non-Gated Detectors

Research on Improving the Accuracy of Laser-Induced Breakdown Spectroscopy Analysis by Considering Plasma Attenuation Rate Characteristics

Long-term Repeatability Improvement Using Beam Intensity Distribution for Laser-Induced Breakdown Spectroscopy

Quantitative aluminum alloys analysis using laser-induced breakdown spectroscopy

Comparison of Libs and Polarization Resolved Libs Emission Spectra for Aluminium Alloy