Abstract:The GMAW process with rotating electrode (GMAW-RE) is a variation of the conventional GMAW process, where the electrode is submitted to a rotating movement, with pre-established rotation diameter and frequency. The method improves the lateral fusion along the sidewalls and contributes to the improvement of narrow gap welding, with significant gains in costs and productivity due to the reduced volume of the deposited weld metal. Although there are some studies about operational characteristics of the process, the literature involving mechanical properties of welded joints remains limited, requiring more experimental evidence to confirm the potential of this process for replacement of conventional GMAW process in industry. This work shows comparative analysis of mechanical and microstructural properties of high-strength steel weld metals obtained by the conventional GMAW and GMAW-RE processes. The weld metals obtained by multipass welding performed in steel plates with dimensions of 500 × 300 × 10 mm were submitted to Charpy-V notch, microhardness tests and metallographic examination from samples removed transversally to the weld bead. The residual stresses were analyzed using X-ray diffraction method at the top surface of the welded joints in the longitudinal and transverse directions of the weld bead. The results showed that the GMAW-RE welding procedure attained the approved standard according to the ASME IX Code, despite using materials with different mechanical strengths once the rupture of the test specimen after tension test has occurred on the base metal 7.4 mm far from fusion line. The joints did not show evidence of lack of fusion along the sidewalls, as verified by the bend tests and metallographic examination. In addition, the GMAW-RE process provided a weld metal with slightly superior mechanical properties compared to the GMAW process due to the more refined microstructure observed with higher amount of acicular ferrite, which favors the impact behavior. The association of higher productivity, reduced costs, lower residual stresses and adequate mechanical properties indicates that GMAW-RE process has a potential alternative for replacement of the GMAW in industrial applications.

Resistência ao Impacto Estrutural de Perfis I Soldados

Análises experimental e numérica de vigas de concreto armado reforçadas ao cisalhamento com barras de aço usando a técnica near-surface mounted (NSM)

Análise da tensão residual em soldagem de revestimento de aço AISI 347L em aço Cr-Mo através do método de medição por coordenadas

Analysis of distortion, corrosion and mechanical properties of welded CSN Civil-300 steel U-type profiles

Caracterização microestrutural e comportamento mecânico das ligas de alumínio AA2139 T3 e T8 soldadas por fricção rotativa com mistura

Microstructure characterization and its relationship with impact toughness of C–Mn and high strength low alloy steel weld metals – a review

INFLUÊNCIA DA RESISTÊNCIA CARACTERÍSTICA À COMPRESSÃO DO CONCRETO (FCK) NA ANÁLISE DE DEFORMAÇÃO DA ESTRUTURA

Undermatched Welding of Ultra-High-Strength Steel S1100 with Metal-Cored Wire: Influence of Welding Positions on Mechanical Properties

Análise mecânica de concretos com substituições parciais de agregados por limalha de aço

Microstructural characterization and mechanical properties of high-strength steel weld metals obtained by GMAW process with rotating electrode (GMAW-RE)

Effect of previous heating treatments conditions and gas metal arc welding (GMAW) on mechanical and microstructural properties of HSLA steel DOMEX 460MC

Microstructure Effect of Heat Input on Ballistic Performance of Welded High Strength Armor Steel

Structural performance of stainless steel sections fabricated by laser-welding, hot-rolling and extrusion

Influence of Chemical Composition on the Mechanical and Microstructural Properties of High Strength Steel Weld Metals Submitted to PWHT

Arc-welded armour steel: A tailored and comparative study of its microstructure and mechanical properties

Fatigue Crack Growth on Flash Butt Welded and Laser Beam Welded Joints in a High-Strength Low-Alloy Steel

Welding of S1100 Ultra high‐Strength Steel Plates with Matching Metal‐Cored Filler Wire: Microstructure, Residual Stresses, and Mechanical Properties

A Comparative Numerical Analysis on the Effect of Welding Consumables on the Ballistic Resistance of SMAW Joints of Armor Steel

Wire and Arc Additive Manufacturing of High‐Strength Low‐Alloy Steel: Microstructure and Mechanical Properties

Load‐carrying capacity of MAG butt and fillet welded joints on high‐strength structural steels of grade S960QL and S960MC

Microstructural Analysis of Partially Diluted Zones in Dissimilar Cladding: EBSD Insights on AWS E 309L Alloy via MIG Process in Single- and Double-Layer Depositions on ASTM A36 Steel