Abstract:Pressure drop (Δp) and collection efficiency (η) are used to evaluate the separation performance of the cyclone separator. In this study, we conducted comparative study of cyclone models using response surface methodology (RSM), back propagation neural network (BPNN), and group method of data handling (GMDH) networks to develop optimal predictive cyclone models. Also, we conducted multi-objective optimization for maximizing model and minimizing model using genetic algorithm (GA). CFD was performed instead of experimental method to get the estimated values for modeling of Δp and η. The validation results of CFD showed 0.5% and 2% errors for Δp and η, respectively, compared with the experimental data. Second, design of experiment (DOE) analysis for 10 cyclone geometrical parameters was executed to obtain the significant geometrical parameters. Vortex finder diameter Dx, inlet width a, inlet height b and cone height Hco have a significant effect on η and Δp. However, interaction effects between the geometrical parameters have small effects. The cyclone models by RSM, BPNN and GMDH based on 25 CFD training set were developed. The predictive performance results by the cyclone models were compared by 25 CFD test set. The GMDH method achieved the best prediction for Δp (R2=99.7, RMSE = 0.102) Radjusted2=98.99, RMSE = 0.0119) than the RSM, BPNN cyclone models. Additionally, uncertainty analysis was performed to estimate the quantitative performance of cyclone models. The results show that the uncertainty width of GMDH models achieved the best prediction (η: ±0.0065, Δp: ±0.0188). Finally, GA was applied to optimize the GMDH models simultaneously. GA generated 70 non-dominant solutions. Reproducibility of five optimal points was validated by using CFD. The trade-off optimal point showed improvement by 24.31%, 18% and 8.79% for Δp d50 and η, respectively.

Multi-objective Optimization Design of Spiral Demister with Punched Holes by Combining Response Surface Method and Genetic Algorithm

Optimization of Dual-Impeller Configurations in a Gas–Liquid Stirred Tank Based on Computational Fluid Dynamics and Multiobjective Evolutionary Algorithm

Multi-objective optimization of a novel vortex finder for performance improvement of cyclone separator

Multi-Objective Optimization of Multistage Centrifugal Pump Based on Surrogate Model

Multi-objective optimization of axial-flow-type gas-particle cyclone separator using response surface methodology and computational fluid dynamics

Multi-Point Optimization on the Diffuser of an Axial Flow Pump

The multi‐objective optimization of an axial cyclone separator in the gas turbine

THE AMINO ACID COMPOSITION OF PROTEINS FROM PLEISTOCENE BONES.

Multi-objective optimization and comparison of surrogate models for separation performances of cyclone separator based on CFD, RSM, GMDH-neural network, back propagation-ANN and genetic algorithm

Parametric optimization of a spiral ground heat exchanger by response surface methodology and multi-objective genetic algorithm

Combining 10 meta-heuristic algorithms, CFD, DOE, MGGP and PROMETHEE II for optimizing Stairmand cyclone separator

Multi-objective optimization investigation on wave plate separator by using Taguchi method

A Fast Multiobjective Optimization Approach to S-duct Scoop Inlets Design with Both Inflow and Outflow

The Design of A Degassing Pump Based on Numerical and Experimental Research

Multi-objective Optimization of a Low Specific Speed Centrifugal Pump Using an Evolutionary Algorithm

Multi-objective optimization of a gas cyclone separator using genetic algorithm and computational fluid dynamics

Multi-objective optimization design of a centrifugal impeller by positioning splitters using GMDH, NSGA-III and entropy weight-TOPSIS

Multi-objective optimization, experimental and CFD approach for performance analysis in square cyclone separator

Structural Parameter Optimization of the Helical Blade of the Variable-Pitch, Downhole, Cyclone Separator Based on the Response Surface Method

Optimization of cavitation performance and hydraulic performance of multistage pump based on response surface method

Multi-objective optimization design of double-hooked corrugated plate dryer based on NSGA-II