Abstract:Suction anchors subjected to inclined loads at the optimal load attachment point are an important taut mooring foundation of deepwater floating production and storage facilities. Sediments in the deepwater areas are generally soft clay with high water contents. It is important for designers to understand failure modes and bearing capacities of suction anchors with taut mooring system in soft clay. Geometry characteristic parameters of anchors, shear strengths of strata and loading cases may be main factors affecting failure modes and bearing capacities of suction anchors. In order to better understand variations of failure modes and bearing capacities resulting from variations of various affecting factors, model tests were conducted under 1g condition for suction anchors with taut mooring system in soft clays. Effects of the friction resistance of the outside wall, geometric characteristic parameters, the variation of soil shear strength along the depth, the loading direction and cyclic loads on the failure mode and the bearing capacity of suction anchors with taut system were studied. Following conclusions were obtained based on model test results. There are three typical failure modes for suction anchors subjected to the inclined load at the optimal load attachment point: (1) the anchor failure is the vertical pullout mode if the vertical ultimate resistance of an anchor is less than the lateral ultimate resistance; (2) the anchor failure is the mode of lateral squeezing strata if the vertical ultimate resistance of an anchor is larger than the lateral ultimate resistance; (3) the anchor failure is the mode of squeezing strata along the inclined upward direction if the lateral ultimate resistance of an anchor is close to the vertical ultimate resistance. For specified stratum, the loading direction and the load case, the failure mode can be changed to increase the bearing capacity of an anchor by optimizing geometric parameters of an anchor. If the lateral ultimate resistance of an anchor is less than the vertical ultimate resistance, the bearing capacity of the anchor does not increase with the increase of the vertical ultimate resistance. The failure of anchors is always the vertical pullout mode if the vertical ultimate resistance of an anchor is less than the lateral ultimate resistance when the loading direction angle from the horizontal decreases from 40 degree to 20 degree for suction anchors with taut mooring system. The cyclic load is an important factor affecting the failure mode and the bearing capacity. The degradation of the vertical ultimate resistance is larger than the degradation of the lateral ultimate resistance under cyclic loads. The failure of an anchor is still the vertical pullout mode under combined static and cyclic loads if the failure of an anchor is the vertical pullout mode under static loads. If the failure of an anchor is lateral failure mode strata under static loads, the failure mode of the anchor will depend on the cyclic degradation of the vertical ultimate resistance under combined static and cyclic loads. When model test results were predicted using the limiting equilibrium analysis method, predicted bearing capacities were basically in agreement with model test results and predicted failure modes were only in qualitative agreement with test results. Copyright © 2012 by the International Society of Offshore and Polar Engineers (ISOPE).

Maximum Force of Inclined Pullout of A Torpedo Anchor in Cohesive Beds

Maximum Vertical Pullout Force of Torpedo Anchors in Cohesive Seabeds at Different Steady Pullout Velocities

Vertical Holding Capacity of Torpedo Anchors in Underwater Cohesive Soils

Centrifuge Modelling of Suction Anchor Subjected to Inclined Load in Soft Clay

The Bearing Capacity of Torpedo Anchor in Clay under Inclined Loading of Mooring Chain

Vertical Pullout Behaviour of a Torpedo Anchor Vertically in Stiff-Over-Soft Cohesive Soil Bed

Penetration Depth of Torpedo Anchor in Cohesive Soil by Free Fall

Free-Fall Penetration Behaviors of A New Dynamically Installed Plate Anchor in Marine Clay

Dynamic Installation Behaviors of A New Hybrid Plate Anchor in Layered Marine Clay

The Installation Behavior and Capacity of Piggy-Backed Anchors for Offshore Wind Turbine

A Self-Penetration Torpedo Anchor with Vibrational Shearing

Penetration Depth of Torpedo Anchor in Two-Layered Cohesive Soil Bed by Free Fall

Numerical Investigations on Pore-Pressure Response of Suction Anchors under Cyclic Tensile Loadings

Numerical investigation on the pull-out capacity of suction anchors in sand considering torsional and mooring line effects

A case study on the seabed trenching assessment and anchor design in clay based on the hydrodynamic calculation of the floater

Behavior of Drag Anchor under Uni-Directional Loading and Combined Loading

A Framework for Mooring and Anchor Design in Sand Considering Seabed Trenches Based on Floater Hydrodynamics

Centrifuge Modeling of the Performance of Suction Anchor in Soft Clay

A Study on Offshore Anchor Selection with a Focus on Torpedo Anchor Stability and Performance

Model tests on failure modes and bearing capacities of suction anchors with taut mooring system

Preliminary tests on the terminal velocity of a torpedo anchor in still water