Abstract:The 2195 Al-Cu-Li alloy is widely utilized for the fabrication of key aerospace vehicle components; hence, an in-depth understanding of its hot deformation behavior is essential for consistently achieving high-performance products. In this study, isothermal compression tests were performed on 2195 Al-Cu-Li alloy ingots in the temperature and strain rate ranges of 250–500 °C and 10 −3 -1 s −1 , respectively. A processing map was established to predict the workability under different conditions. The corresponding microstructures were examined to reveal their hot deformation mechanism. Results demonstrated that the processing map was divided into four distinct domains. The unstable zone was located in the 250–375 °C/10 −1.5 -1 s −1 and 250–275 °C/10 −2.5 –10 −1.5 s −1 , temperature/strain rate regimes, in which deformation bands and flow localization were observed. The deformation bands blocked dislocations and compromised the dynamic recrystallization (DRX) behavior, hence damaging the microstructure. Further, large coarse T 1 phases precipitated in the 325–410 °C/10 −2.5 –10 −3 s −1 regime, which led to the formation of heterogeneities in the microstructure, corresponding to a minimum workability in the processing map. The optimal hot-working domain for the 2195 alloy was determined to be 460–500 °C/10 −3 –10 −2 s −1 , and the dominating hot deformation mechanisms were DRX and dynamic recovery (DRV). Specifically, continuous and discontinuous DRX behaviors dominated in the 300–400 °C/10 −3 s −1 and 450–500 °C/10 −3 s −1 regimes, respectively. DRX gradually weakened as the strain rate increased at 500 °C. Further, the weakening of DRX was only minimally affected by temperature at 400–500 °C during high-speed deformation (1 s −1 ). The results reported herein can provide valuable insights into the hot working of Al-Cu–Li alloys.

Double Identification of the Optimal Hot Deformation Parameter Windows for AlCu4SiMg Alloy

Hot Deformation Characteristics and Processing Parameter Optimization of Al–6.32Zn–2.10Mg Alloy Using Constitutive Equation and Processing Map

The hot deformation characteristics and the associated microstructural evolution of an Al-Cu-Li-Zn alloy studied by constitutive equations and processing maps

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys

Determining Thermal Parameter Windows of 40Cr10Si2Mo Steel from an Enhanced Processing Map

Hot Deformation and Processing Map of As-Homogenized Mg–9Gd–3Y–2Zn–0.5Zr Alloy

Hot deformation characteristics and processing parameter optimization of 2219 Al alloy using constitutive equation and processing map

Investigation of deformation behavior and strain-induced precipitations in Al-Zn-Mg-Cu alloys across a wide temperature range

Hot Deformation Behavior and Microstructure Evolution of a Novel High-Zn Containing Al-Zn-Mg-Cu-Zr Alloy

Hot Deformation Behavior and Processing Map of Al-Zn-Mg-Cu-Zr Alloy

Hot deformation and dynamic recrystallization in Al-Mg-Si alloy

Hot Deformation Behavior and Processing Maps of an As-Cast Al-5Mg-3Zn-1Cu (wt%) Alloy

Hot Workability of a Spray Formed 2195 Aluminum-Lithium Alloy Based on an Improved Isothermal Processing Map and Drx ‘C-Curve’

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy

Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: A study with processing map

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Hot Compression Behavior and Processing Map of Homogenized Al-Mg-Si Alloy

Dynamic recrystallization mechanisms of as-forged Al–Zn–Mg-(Cu) aluminum alloy during hot comp.ression deformation

Hot Processing Map and Dynamic Precipitation Behavior of 1460 Al–Li Alloy During Hot Deformation

A New, Precise Constitutive Model and Thermal Processing Map Based on the Hot Deformation Behavior of 2219 Aluminum Alloy

Determination of Dynamic Recrystallization Parameter Domains of Ni80A Superalloy by Enhanced Processing Maps