Abstract:In this work, a commercial magnesium alloy, AZ31B in hot-rolled condition, has been subjected to severe plastic deformation via four passes of equal channel angular pressing (ECAP) to modify its microstructure. Electron backscatter diffraction (EBSD) was used to characterize the microstructure of the as-received, ECAPed and mechanically loaded specimens. Mechanical properties of the specimens were evaluated under both compression and tension along the rolling/extrusion direction over a wide range of strain rates. The yield strength, ultimate strength and failure strain/elongation under compression and tension were compared in detail to sort out the effects of factors in terms of microstructure and loading conditions. The results show that both the as-received alloy and ECAPed alloy are nearly insensitive to strain rate under compression, and the stress strain curves exhibit clear sigmoidal shape, pointing to dominance of mechanical twinning responsible for the plastic deformation under compression. All compressive samples fail prematurely via adiabatic shear banding followed by cracking. Significant grain size refinement is identified in the vicinity of the shear crack. Under tension, the yield strength is much higher, with strong rate dependence and much improved tensile ductility in the ECAPed specimens. Tensile ductility is even much larger than the malleability under compression. This supports the operation of < c + a > dislocations. However, ECAP lowers the yield and flow strengths of the alloy under tension. We attempted to employ a mechanistic model to provide an explanation for the experimental results of plastic deformation and failure, which is in accordance with the physical processes under tension and compression. (C) 2015 Elsevier Ltd. All rights reserved.

Mechanical Properties and Failure of ECAE Processed Mg97Y2Zn1 at Different Strain Rates

Microstructural Evolution and Mechanical Properties of Mg95.5Y3Zn1.5 Alloy Processed by Extrusion and ECAP

Effect of ECAE Conditions on the Microstructure, Texture and Mechanical Properties of an Extruded Mg–Zn–Y–Zr Alloy

Microstructure and Mechanical Properties of Two–phase Mg–10.73Li–4.49Al–0.52Y Alloy Processed by ECAP at Different Routes

Microstructure and Mechanical Behavior of Ecap Processed Az31b over A Wide Range of Loading Rates under Compression and Tension

Effect of Solution Treatment on Microstructure Evolution and Mechanical Properties of Mg-6.0Zn-0.6Y-0.5Zr Alloy Processed by Equal Channel Angular Extrusion

Microstructure and Mechanical Properties of Ultrafine Grained Mg97Y2Zn1 Alloy Processed by Equal Channel Angular Pressing

Microstructure Evolution and Mechanical Behavior of Mg-10Gd-3Y-0.4Zr Alloy Processed by ECAP at High Temperature

Characterization of microstructure in high strength Mg 96Y 3Zn 1 alloy processed by extrusion and equal channel angular pressing

A Study of Microstructure Evolution for Mg Alloy Subjecting to Multi-Pass Equal Channel Angular Extrusion

Influence of ECAP Routes on Microstructure and Mechanical Properties of Mg–Zn–Ca Alloy

Microstructure Evolution and Mechanical Properties of AZ 31 Mg Alloy Processed by Equal Channel Angular Extrusion

Microstructure and tensile property of the ECAPed pure magnesium

Preparing Mg-6Al alloy with high mechanical properties and fine grains by equal channel angular extrusion

Microstructure and Tensile Properties of A Mg-Zn-Y-Zr Alloy Containing Quasicrystal Phase Processed by Equal Channel Angular Pressing

Microstructure, Texture and Mechanical Properties of Mg-1.5mn-0.3ce Magnesium Alloy Reformed by Equal Channel Angular Pressing

Mechanical Properties and Microstructure of AZ31B Magnesium Alloy Processed by I-ECAP

Microstructure and mechanical properties of AZ31 Mg alloy processed by two-step equal channel angular extrusion

High temperature deformations and microstructural evolutions of Mg alloy laminated composites fabricated by ECAE

Microstructural evolution and mechanical response of duplex Mg-Li alloy containing particles during ECAP processing

Microstructure Evolution of AZ Series Magnesium Alloys During Cyclic Extrusion Compression