Abstract:Surface Acoustic Wave (SAW) technique is one of the most promising Micro Electro Mechanical Systems (MEMS) based detection methods for a variety of applications. SAW sensor is based on the modulation of Rayleigh waves that travel near the surface of a piezoelectric substrate. Advent of MEMS technology has led to the development of SAW sensors which are widely used in chemical sensing, medical, industrial, telecommunication and biological applications. The main focus of this paper is to devise and characterize a generic SAW structure and study the acoustic properties at various environmental conditions before depositing the sensing layer/analyte for any particular application. In this work, a SAW device was designed using COMSOL Multiphysics for a resonant frequency of 100 MHz with 40 μm wavelength on Lithium Niobate (LiNbO3) piezoelectric substrate. The optimized device structure was fabricated using thin film deposition and UV photolithography. The resonant frequency of the fabricated device (97.63 MHz) matched closely with the simulation results (100 MHz) and theoretical results (100 MHz). The device was subjected to various environmental conditions to study the influence on the resonant frequency. The SAW structure showed a resonant frequency shift of 90 KHz in steam environment, ~ 1MHz when heated to 150°C and ~120 KHz when exposed to 80% RH. The device exhibited a linear shift in resonant frequency under all tested environmental conditions with a consistent baseline and good repeatability.

Observational and Theoretical Validation of Longitudinal Type Surface Acoustic Wave Devices

Effect of Variable Cross-Section Rod on Laser-Induced Surface Acoustic Waves.

A Laser Probe Based on a Sagnac Interferometer with Fast Mechanical Scan for RF Surface and Bulk Acoustic Wave Devices

Analysis Of Rayleigh-Mode Spurious Response Using Finite Element Method/Spectrum Domain Analysis For Surface Acoustic Wave Resonator On Nonflat Sio2/Al/Linbo3 Structure

Fabrication of Si / Inlaid-IDT / LiNbO 3 Structure for Acoustic Boundary Wave Devices

High-Speed Laser Probing System for Surface Acoustic Wave Devices Based on Knife-Edge Method

High Performance Lithium Niobate Surface Acoustic Wave Transducers in the 4–12 GHz Super High Frequency Range

A Simulated Investigation of Lithium Niobate Orientation Effects on Standing Acoustic Waves

Analysis of Rayleigh-Mode Spurious Response Using Finite Element Method/Spectrum Domain Analysis for Surface Acoustic Wave Resonator on Nonflat SiO<sub>2</sub>/Al/LiNbO<sub>3</sub> Structure

3.5 GHz longitudinal leaky surface acoustic wave resonator using a multilayered waveguide structure for high acoustic energy confinement

The Modeling and Analysis of Surface Acoustic Wave Filter Based on IDT/AIN/LiNbO3

A High Velocity and Wideband SAW on a Thin LiNbO3 Plate Bonded on a Si Substrate in the SHF Range

Development of Fast-Scanning Laser Probe System Based on Knife-Edge Method for Diagnosis of Rf Surface Acoustic Wave Devices

8E-6 Extended FEM/SDA Software for Characterising Surface Acoustic Wave Propagation in Multi-Layered Structures

Improvement of Detection System for a Fast-Scanning and Phase-Sensitive Laser Probe for Surface Acoustic Wave Devices in 2 GHz Range

Development of a High-Speed, Phase-Sensitive Laser Probe System for RF Surface Acoustic Wave/bulk Acoustic Wave Devices with an Absolute Vibration Amplitude Measurement Function

Laser Probe System for 5 GHz SAW/BAW Devices

Influence of Coupling with Shear Horizontal Surface Acoustic Wave on Lateral Propagation of Rayleigh Surface Acoustic Wave on 128 Degrees Yx-Linbo3

Design Optimization of Surface Acoustic Wave Devices and Investigation of Fabricated Devices under Temperature, Humidity and Steam Environments

Characterization of Surface Acoustic Wave Propagation in Multi-Layered Structures Using Extended Fem/Sda Software

High Resolution Laser-Interferometric Probing of SAW Devices