Abstract:Magnesium-zinc-calcium alloys have unique advantages of being used as biomedical bone implants since their mechanical properties and biocompatibility are similar to human tissues. However, insufficient strength and poor corrosion resistance have been the major problems to stunt the application. In this paper, the changes of microstructure, mechanical properties and corrosion resistance of ternary Mg-3Zn-0.2Ca (wt.%) with different contents of Mn (0.3, 0.5, 0.7, 0.9, wt.%) are studied. With the increase of Mn content, the grain size of as-cast alloy first decreases and then increases, this indicates that the amount of Mn affects the degree of subcooling of the alloy. At the 320°C/24 h homogenizing treatment, the large and uneven dendrites are transformed into uniform equiaxed grains, the mechanical properties of alloys with different Mn contents are different on the basis of Mg-3Zn-0.2Ca (wt.%) alloy. The five alloys were extruded into bar with a diameter of 8 mm through hot-extrusion process. Quaternary Mg-3Zn-0.2Ca-XMn (X = 0.3, 0.5, 0.7, 0.9) (wt.%) alloys are investigated and the results show that 0.5 wt.% Mn alloy has the best yield tensile strength (YS) (302 MPa) and good ultimate tensile strength (UTS) (327 MPa). The reason is that the different contents of Mn restrain the dynamic recrystallization in extrusion process, which remarkedly reduced the grain size. Moreover, each alloy is investigated by electrochemical measurements at 37°C in a simulated body fluid (SBF). The electrochemical results show that the corrosion potential of Mn-contained alloys are increased compared to ternary Mg-3Zn-0.2Ca (wt.%) alloy, and 0.5 wt.% Mn-contained alloy performs the best result.

Effects of Mn Addition on the Corrosion Behaviors of Zr-Sn-Nb-Fe-Mo Alloys

EFFECT OF Sb AND Mn ADDITIONS ON THE CORROSION BEHAVIOUR OF Zn

Effect of Mn Addition on Microstructure and Mechanical Properties of Cast Al-2li-2cu-0.8mg-0.4zn-0.2zr Alloy

Improved Strength and Enhanced Pitting Corrosion Resistance of Al-Mn Alloy with Zr Addition

Effect of Mn on Corrosion Behavior of Mg-9Al-2Sn

Effect of Zr Addition on Microstructure and Properties of Al–Mn–Si–Zn-based Alloy

The effect of Mn addition on corrosion behaviour of equiatomic CoCrFeNi high entropy alloys in NaCl solution

EFFECT OF Mn ON CORROSION BEHAVIOR OF Zn IN A SIMULATED SOLUTION FOR MARINE ATMOSPHERE

Effect of trace Mn modification on the microstructure and corrosion behavior of Sn−9Zn solder alloy

Effect of Mn Content on the Microstructure, Mechanical Properties and Corrosion Behavior of Ti–Nb–Zr–Mn Alloys Processed Via Spark Plasma Sintering

Effect of Mn Element Addition on the Microstructure, Mechanical Properties, and Corrosion Properties of Mg-3Zn-0.2Ca Alloy

Corrosion behaviors of Zr-Sn-Nb alloys: Influence of different concentration dissolved oxygen environment and trace V element on the anti-corrosion properties

The Effect of 0.4 Wt.% Mn Addition on the Localized Corrosion Behaviour of Zinc in a Long-Term Experiment

Influences of Mn Content on the Microstructures and Mechanical Properties of Cast Al-3Li-2Cu-0.2Zr Alloy

Effect of Mo Addition on Corrosion Behavior of High-Entropy Alloys CoCrFeNiMox in Aqueous Environments

Effects of Mn Addition on the Microstructure and Mechanical Properties of Cast Mg–9Al–2Sn (wt.%) Alloy

Coupling Effect of Mn Addition and Deformation on Mechanical and Electrical Properties of Al-Zr Alloys

Effects of a Small Addition of Mn on the Corrosion Behaviour of Zn in a Mixed Solution

Development of Biomedical Ti-Nb-Zr-Mn Alloys with Enhanced Mechanical Properties and Corrosion Resistance

Effect of Microstructure on Corrosion Behavior of A Zr-Sn-Nb-Fe-Cu-O Alloy

Mechanical properties and corrosion behavior in molten zinc of Mo–ZrO 2 alloys