Abstract:This study aims to improve the performance of magnesium phosphate cement-based engineered cementitious composites (MPC-ECC) and establish a systematic design method. The MPC-ECC with ultra-high ductility was prepared with the polyethylene (PE) fibers. The effect of the magnesium oxide to potassium dihydrogen phosphate mass ratio (M/P), quartz sand particle size (Sd), water to solid mass ratio (W/S), sand to binder mass ratio (S/B), fly ash (FA) content and fiber volume fraction (Vf) on the micro-mechanical properties and macro-mechanical properties of MPC-ECC were explored. The macro-mechanical properties of MPC-ECC with different curing temperatures and curing ages were also tested. And the SEM test was carried out to analyze the morphology of the MPC-ECC. The results showed that the ultimate tensile strain of MPC-ECC with optimal proportion can reach 7.1%. Even curing at −10 °C for 7 days, the ultimate tensile strain can reach 5.6%, and the compressive strength can reach nearly 20 MPa. And the microstructure is characterized by a highly dense morphology. Additionally, with the increase of M/P, the compressive strength of MPC-ECC increases, but the ultimate tensile stress decreases. The MPC-ECC with the Sd of 150–180 mesh shows significant strain hardening performance, and its ultimate tensile strain can exceed 5%. The large W/S is helpful to improve strain hardening performance, especially when the S/B is 0.2. In addition, when the FA content is 30% or 40%, the strain hardening performance of MPC-ECC is significant. The quantitative association model between ultimate tensile strain and pseudo strain-hardening indices was established. According to the association model, the design method of MPC-ECC was established, based on which the MPC-ECC with desired ductility can be realized. Meanwhile, the PSH σ and PSH J are recommended to reach 2.15 and 25.1, respectively, at the same time for the MPC-ECC with ultimate tensile strain of above 3%.

Optimization of printing precision and mechanical property for powder-based 3D printed magnesium phosphate cement using fly ash

Evaluation of Mechanical and Microscopic Properties of Magnesium Phosphate Cement-Based Concrete with Different Fly Ash Additions

Influence of high‐sulfur fly ash on the microstructure and properties of magnesium phosphate cement

Improving mechanical properties of 3D printed mortar by exploiting synergistic effects of fly ash microsphere and nano-silica

Mechanical Properties and Hardening Mechanism of Magnesium Ammonium Phosphate Cements Modified by Fly Ash

Thermally stimulated stiffening and fly ash's alkaline activation by Ca(OH) 2 addition facilitates 3D-printing

Development and design of ultra-high ductile magnesium phosphate cement-based composite using fly ash and silica fume

Effect of Coal Fly Ash and CO2 Curing on Performance of Magnesium Potassium Phosphate Cement

Optimization of Magnesium Potassium Phosphate Cements Using Ultrafine Fly Ash and Fly Ash

Systematic approach for printability evaluation and mechanical property optimization of spray-based 3D printed mortar

Factors Influencing the Properties of Extrusion-Based 3D-Printed Alkali-Activated Fly Ash-Slag Mortar

A new strategy to enhance 3D printability of cement-based materials: In-situ polymerization

Study on flexural resistance and hydration mechanism of magnesium phosphate cement

Magnesium phosphate cement-based engineered cementitious composites with polyethylene fibers: Performance improvement and design method

Experimental Research on Mechanical Properties and Microstructure of Magnesium Phosphate Cement-Based High-Strength Concrete

Effects of bentonite, diatomite and metakaolin on the rheological behavior of 3D printed magnesium potassium phosphate cement composites

A novel method for improving the printability of cement-based materials: Controlling the releasing of capsules containing chemical admixtures

Influence of Ultrafine Fly Ash and Slag Powder on Microstructure and Properties of Magnesium Potassium Phosphate Cement Paste

Mechanical Performance Optimization in Spray-Based Three-Dimensional-Printed Mortar Using Carbon Fiber

Properties and microstructure of a low-carbon clinker-free cementitious binder and its extrusion-based printing performance

WFT-based assessment of the rheological characteristics, particle packing, and buildability of Pcc-FA-GGBFS composite materials for 3D printing