Abstract:Morphology development at the fiber/matrix interphase in fiber-reinforced isotactic polypropylene composites is a widely studied topic. While the application of shear flow may strongly enhance the nucleation density around the fiber, little is known about the influence of fibers on the crystallization of polypropylene subjected to an extensional flow. In this work, the flow around a single glass fiber upon uniaxial elongation of the melt is examined using X-ray scattering and diffraction techniques and compared to the response measured for the neat matrix. A comparison between a neat and compatibilized matrix is made given the strong influence of the addition of an adhesion modifier on the bulk crystallization kinetics of polypropylene. The flow is applied using an in-house-built filament stretching extensional rheometer, which, due to its midfilament control scheme, allows for in situ X-ray experiments. Combined small-angle X-ray scattering/wide-angle X-ray diffraction patterns are acquired during the flow and subsequent crystallization step. Postcrystallization area scans of the filament show that the introduction of a single glass fiber gives rise to the development of β-phase crystals, particularly in the area around the fiber ends, and in contrast to what is observed for the matrix materials alone, where solely α-phase is found. Surprisingly enough, the addition of a single fiber (0.00045 vol %) alters the crystallizing polymorph in almost the entire filament. However, the addition of the adhesion modifier hinders the formation of β-phase crystals around the fiber due to an acceleration of the bulk crystallization kinetics. Finite element simulations provide insight into the flow field around the fiber during stretching and demonstrate that the flow is no longer uniaxial extension, but dominated by shear, even though the volumetric amount of fiber as compared to the matrix is negligible. These findings explain the experimental observation of substantial β-phase formation after the introduction of a single fiber, while this is not observed in the matrix material. Worth noting, the formation of β-phase polypropylene depends not only on the presence and the strength of the flow but predominantly on the type of flow, i.e., shear as opposed to elongation.

Influence of Diameter on the Templated Crystallization of Polyethylene/Carbon Material Fiber Composites under Intense Shear Flow.

Influence of Nanofiller Dimensionality on the Crystallization Behavior of HDPE/carbon Nanocomposites

Filled Polyolefin Composites Prepared From In-Situ Polymerization Via A Catalyst-Supported Approach - I. Morphology Of Pe In Carbon Black(Cb)/Pe In-Situ Composites

Influence of Reduced Graphene Oxide on the Rheological Response and Chain Orientation on Shear Deformation of High Density Polyethylene

Effects of Carbon Nanofibers on Crystalline Structures and Properties of Ultrahigh Molecular Weight Polyethylene Blend Fabricated Using Twin‐screw Extrusion

Fiber-Induced Crystallization in Elongational Flows

Synergistic and Competitive Effects of Temperature and Flow on Crystallization of Polyethylene during Film Blowing

DSC and Morphological Studies on the Crystallization Behavior of Β-Nucleated Isotactic Polypropylene Composites Filled with Kevlar Fibers

More Dominant Shear Flow Effect Assisted by Added Carbon Nanotubes on Crystallization Kinetics of Isotactic Polypropylene in Nanocomposites

Effect of deformation ratio of flow-induced crystallization on polyethylene in crystalline behavior, thermal stability, and tensile loading: a molecular dynamics simulation

Effect of processing parameters on degree of crystallinity and mechanical performance of CF/PEKK aerospace composites

Mechanical Properties, Melting and Crystallization Behaviors, and Morphology of Carbon Nanotubes/Continuous Carbon Fiber Reinforced Polyethylene Terephthalate Composites

Shear-induced crystallization in a blend of isotactic polypropylene and high density polyethylene

Molecular Dynamics Simulation on the Crystallization Behavior of Cyclic Polyethylene Affected by Functionalized Carbon Nanotubes

Inherent relationship between process parameters, crystallization and mechanical properties of continuous carbon fiber reinforced peek composites

Effect of Flowing Preformed Spherulites on Shear-Induced Melt Crystallization Behaviors of Isotactic Polypropylene

Crystal morphology and tensile properties of LLDPE containing PP fibers as obtained via dynamic packing injection molding

The effect of cooling rate on crystallization behavior and tensile properties of CF/PEEK composites

Morphological Structure of Melt-Drawn Films of Polyethylene Containing Small Amount of Copolymerized Component

Unique crystal morphology and tensile properties of injection-molded bar of LLDPE by adding HDPE with different molecular weights

The influence of formation temperatures on the crystal structure and mechanical properties of ultrahigh-molecular-weight polyethylene/high-density polyethylene-blend fibers prepared by melt spinning