Abstract:Comparator is a connection between the analog and digital worlds [1] –[5]. A low-noise and low-power comparator is important in many applications, such as SAR ADC. Traditionally, such a comparator is realized as the Strong-Arm (SA) latch. It has the advantage of fullydynamic operation and embedded pre-amplifier. However, its preamplifier gain is as low as 4 5, which increases the input-referred noise and offset. In recent years, there are many efforts to design a more efficient dynamic comparator. Both [1] and [2] improve the dynamic-bias comparator of [3] that is based on the subthreshold-biased input transistors for large $\mathrm{g}_{\mathrm{m}} / \mathrm{l}_{\mathrm{D}}$. Among them, [1] uses a floating inverter amplifier (FIA) as the pre-amplifier. This pre-amplifier has a large voltage gain of approximately 30, which suppresses the noise and offset effectively. It realizes a 2-times current reuse, improving the energy efficiency. However, the energy efficiency can hardly be improved further, since it is independent of the device sizes. The current reuse is also limited to 2 times, which is far away from the maximum possible times (for example, 4 times in this work). [2] uses a charge pump and capacitive positive feedback for faster speed but at the cost of increased power. Its noise is also as large as $174 \mu \mathrm{V} \mathrm{rms}$, which is 3.8 times larger than [1].

A 0.6-V Tail-Less Inverter Stacking Amplifier with 0.96 PEF.

A 1V 0.25uw Inverter-Stacking Amplifier with 1.07 Noise Efficiency Factor

A 1-V 0.25- $\mu \text{w}$ Inverter Stacking Amplifier with 1.07 Noise Efficiency Factor

3.10 A 0.69/0.58-PEF 1.6nW/24nW Capacitively Coupled Chopper Instrumentation Amplifier with an Input-Boosted First Stage in 22nm/180nm CMOS.

A 24-Ghz Voltage-Combined Stacked Power Amplifier with Current-Sharing Technique in 65-Nm CMOS

Compact 50-62 GHz Current-Reused Low-Noise Amplifier with Gate-Drain Transformer Feedback

A 2.1/5.2-NEF/PEF Capacitively Coupled Instrumentation Amplifier with Fast - Settling for Biosensor

A Compact 2.1–39 GHz Self-Biased Low-Noise Amplifier in 65 Nm CMOS Technology

Ultralow Power E-Band Low-Noise Amplifier with Three-Stacked Current-Sharing Amplification Stages in 28-Nm CMOS

Design of Differential Variable-Gain Transimpedance Amplifier in 0.18 Μm SiGe BiCMOS

An Inductorless 5-GHz Differential Dual Regulated Cross-Cascode Transimpedance Amplifier using 40 nm CMOS

A 153μw 26nv/√hz Readout Circuit with BW and Power Scalability Using Capacitively-Coupled Chopper Floating Inverter Amplifier Embedded in a Discrete-Time ΔΣ Modulator

A 0.69-Noise-efficiency-factor 4 X-Current-reuse Dynamic Comparator with A Stacking FIA

A Novel Capacitively-Coupled Instrumentation Amplifier Employing Chopping and Auto-Zeroing.

A PVT-Robust Transimpedance Amplifier for Ultra-Low Current Sensing

Fully Integrated CMOS Power Amplifier With Efficiency Enhancement at Power Back-Off

Design and Implementation of A High-Precision Low-Power Instrumentation Amplifier

A 3.6 Μw 60 Nv/sqrthz Capacitively-Coupled Instrumentation Amplifier for Biopotential Signal Recordings.

A 0.45v 687pw Low Noise Amplifier Front-End with 1.73 Nef for Energy-Scavenging Iot Sensors

Power-to-Noise Optimization in the Design of Neural Recording Amplifier Based on Current Scaling, Source Degeneration Resistor, and Current Reuse

High Efficiency Triple-Stacked Class-E Power Amplifier with Novel Dynamic Biasing Network