Abstract:Purpose 3D printing products are progressively being utilized in the dental field and for achieving suitable mechanical properties. The post-curing process is essential after fabricating a restoration using 3D printed resin. This study aimed to evaluate the potential use of a handheld multiwavelength light-emitting diode (LED) dental light-curing unit (LCU) for post-curing of 3D printed resin by measuring the microhardness and biaxial strength of the post-cured resin. Methods 1-mm and 2-mm thick resin discs (n=6, each) were 3D printed using a DLP printer (Zenith L2; Dentis). After rinsing with ethyl alcohol, the discs were further post-cured by a dental LCU (VALO; Ultradent) for 3seconds per cycle at 3,200mW/cm2. Post-curing was repeated either on one side from the top surface: 2 cycles (V2S), 4 cycles (V4S), 8 cycles (V8S); or on both sides from the top and bottom surface: 1 cycle (V1D), 2 cycles (V2D), 4 cycles (V4D) for each side. Afterwards, microhardness and biaxial strengths of the discs were compared to those post-cured by conventional desktop curing units (Cure Box; ODS [DCB] and Zenith Cure; Dentis [DZC]) (n=6, each) and those without post-curing (NC) (n=6). Data were analyzed using One-way ANOVA, Tukey HSD Test for multiple comparisons, and independent t-test to compare the values between the 1-mm-thick and 2-mm-thick discs (α=0.05). Results Microhardness of the discs varied between the 1-mm and 2-mm-thick discs and between the top and bottom surfaces, depending on the post-curing methods. In both thicknesses, V8S and V4D provided microhardness values of the top surface comparable to the control group, while DCB and V4D obtained the highest microhardness on the bottom surface (P< 0.05). The 1-mm-thick discs showed greater biaxial strength than the 2-mm-thick discs, except for NC and DZC. V4D provided the highest biaxial strength in both thicknesses (P< 0.05) that were comparable to the conventional desktop curing units (P> 0.05). Conclusion The dental LCU showed increased microhardness and biaxial strength of the post-cured 3D printed discs, particularly with multiple curing cycles from both sides. The handheld multiwavelength LCU has the potential to be used as a viable alternative to conventional desktop curing units.

Mechanics of Shape Distortion of DLP 3D Printed Structures During UV Post-Curing.

Digital Laser Direct Writing of Internal Stress in Shape Memory Polymer for Anticounterfeiting and 4D Printing.

Design for the reduction of volume shrinkage-induced distortion in digital light processing 3D printing

Method for Obtaining Light Curing Printing Condition Based on New Theoretical Description

High-fidelity and high-efficiency additive manufacturing using tunable pre-curing digital light processing

Minimizing Polymer Curl Distortion and Heat Impact to Improve Digital Light Processing Printing Accuracy via Subdivision Method

Printing Depth Modeling, Printing Process Quantification and Quick-Decision of Printing Parameters in Micro-Vat Polymerization

Modeling the Printability of Photocuring and Strength Adjustable Hydrogel Bioink During Projection-Based 3D Bioprinting.

Simulation and Process Analysis of DLP 3D Printing with High-strength Resin

Theoretical prediction and experimental validation of the digital light processing (DLP) working curve for photocurable materials

Effect of ultraviolet post-curing, laser power, and layer thickness on the mechanical properties of acrylate used in stereolithography 3D printing

Impact of Shape Transformation of Programmable 3D Structures on UV Print Quality

Multi-step exposure method for improving structure flatness in digital light processing-based printing

Mechanical isotropy and postcure shrinkage of polydimethylsiloxane printed with digital light processing

Effects of exposure time and printing angle on the curing characteristics and flexural strength of ceramic samples fabricated via digital light processing

Shape memory polymers structure with different printing direction: Effect of fracture toughness

Process Analysis of DLP Photocuring 3D Printing with Modified High-strength Resin

Review on digital light processing (DLP) and effect of printing parameters on quality of print

Post-curing of 3D printed resin using dental light curing unit

Effect of functionality of diluents on digital light processing (DLP) based three‐dimensional (3D) printing of UV‐curable bisphenol A‐based epoxy acrylate resin

Top-down digital light processing 3D printing of composite structures using carbon fiber modified UV curable resin