Abstract:The abundant oxygen‐related defects (e.g., O vacancies, O‐H) in the TiO2 electron transport layer results in high surface energy, which is detrimental to effective carrier extraction and seriously impairs the photovoltaic performance and stability of perovskite solar cells. Here, novel surface energy engineering (SEE) was developed by applying a surfactant of heptadecafluorooctanesulphonate tetraethylammonium (HFSTA) on the surface of the TiO2. Theoretical calculations show that the HFSTA‐TiO2 is less prone to form O vacancies, leading to lower surface energy, thus improving the carrier‐extraction efficiency. The experimental results show that superior perovskite film was obtained due to the reduced heterogeneous nucleation sites and improved crystallization process on the modified TiO2. Furthermore, the flexible long alkyl chains in HFSTA considerably relieved the compressive stresses at the buried interface. By combining the passivation of TiO2, crystallization process modulation and stress relief, a champion PCE up to 25.03% was achieved. The device without encapsulation sustained 92.2% of its initial PCE after more than 2500 h storage under air ambient with relative humidity of 25–30%. The SEE of a buried interface paves a new way towards high‐efficiency, stable perovskite solar cells. This article is protected by copyright. All rights reserved

Engineering the Underlying Surface to Manipulate the Growth of 2D Perovskites for Highly Efficient Solar Cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Crystalline Liquid-like Behavior: Surface-Induced Secondary Grain Growth of Photovoltaic Perovskite Thin Film

Interfacial Engineering Enables High Efficiency with a High Open-Circuit Voltage above 1.23V in 2D Perovskite Solar Cells

Efficient and scalable perovskite solar cells achieved by buried interface engineering

Interface engineering of highly efficient perovskite solar cells

Controlled Dion-Jacobson Low-Dimensional Surface Phase Enables Highly Efficient and Stable Perovskite Solar Cells

Holistic energy landscape management in 2D/3D heterojunction via molecular engineering for efficient perovskite solar cells

Highly Efficient and Stable 2D 3D Perovskite Solar Cells Fabricated by Interfacial Modification

Fast and Controllable Electric-Field-Assisted Reactive Deposited Stable and Annealing-Free Perovskite toward Applicable High-Performance Solar Cells

Construction of 2d/3d/2d‐structured Perovskite for High‐Performance and Stable Solar Cells

Molecular Engineering for Two-Dimensional Perovskites with Photovoltaic Efficiency Exceeding 18%

Surface Reconstruction and In Situ Formation of 2D Layer for Efficient and Stable 2D/3D Perovskite Solar Cells

De-templated crystallization in 2D perovskites for enhanced photovoltaic efficiency

Spacer Engineering of Diammonium‐Based 2D Perovskites toward Efficient and Stable 2D/3D Heterostructure Perovskite Solar Cells (Adv. Energy Mater. 2/2022)

Enhancing Perovskite Solar Cell Performance Through Surface Engineering of Metal Oxide Electron-Transporting Layer

Solution‐Phase Epitaxial Growth of Perovskite Films on 2D Material Flakes for High‐Performance Solar Cells

Infiltrated 2D/3D Heterojunction with Tunable Electric Field Landscape for Robust Inverted Perovskite Solar Cells with over 24% Efficiency

Rational Design of Ferroelectric 2D Perovskite for Improving the Efficiency of Flexible Perovskite Solar Cells Over 23

Reconstructing the Amorphous and Defective Surface for Efficient and Stable Perovskite Solar Cells

Surface Energy Engineering of Buried Interface for Highly Stable Perovskite Solar Cells with Efficiency Over 25%