Abstract:Inconel 617 nickel-based superalloy with 3 mm wall thickness was welded by laser beam using two different heat input welding parameters. The microstructure of the welded joint was observed by optical microscope and scanning electron microscope, and the mechanical properties of the welded joint at room temperature (25celcius) and high temperature (900celcius) were tested. The results show that the laser welding heat input has a significant effect on the microstructure and mechanical properties of Inconel 617 welded joints. The front width of the laser weld obtained by high heat input (200 J/mm) process parameters is 3.88 mm. The grain size in the middle of the weld fusion zone is coarse, and the grain orientation is disordered. The secondary dendrite arm spacing in the middle of the weld is large (6.71 mu m). The carbide particle size between the dendrites is coarse, and the solidification microsegregation of Mo, Cr alloy elements is serious. The width of heat affected zone is about 0.29 mm. The eutectic structure of gamma+carbide is formed in the grain boundary and grain interior. This is because during the heating process of the welding, the spherical carbide particles and the surrounding austenite in the heat-affected zone liquefy and the eutectic structure is formed during the solidification process after welding. The front width of the laser weld obtained by low heat input (90 J/mm) process parameters is 2.28 mm, the grains inside the weld are columnar which is formed by epitaxial growth along the fusion line and directional solidification along the heat flow direction. The secondary dendrite arm spacing in the middle of the weld is small (2.26 mu m), the carbide particles between dendrites are small, and the width of heat affected zone is about 0.15 mm. The tensile strength test at room temperature (25celcius) shows that the welded joints obtained under high heat input fracture from the middle of the weld, and the tensile strength and elongation decrease, which is caused by the segregation of solid solution elements in the weld. The welded joints obtained under low heat input fracture from the base metal. At high temperature (900celcius), all samples fracture from the base metal, which is due to the weakening of the grain boundary of the base metal at high temperatures.

Effect of Preheating on Microstructure and Low-Temperature Toughness for Coarse-Grained Heat-Affected Zone of 5% Ni Steel Joint Made by Laser Welding

Effects of Preheating Temperature on Cold Cracks, Microstructures and Properties of High Power Laser Hybrid Welded 10ni3crmov Steel

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

Effect of Preheating Temperature on the Microstructure of QSTE420TM+XC45 Dissimilar Steel Laser Welded Joints

Effect of Pre-Weld Heat Treatment on the Microstructure and Properties of Coarse-Grained Heat-Affected Zone of a Wind Power Steel after Simulated Welding

Effect of Preheating on the Defects and Microstructure in NG-GMA Welding of 5083 Al-alloy

Low temperature impact toughness of laser hybrid welded joint of high strength low alloy steel

Probing Microstructural Evolution Behaviors in Laser Welding of Dissimilar Gh4169/Gh3039 Subjected to Varied Preheating Temperatures

Effect of Preheating on the Microstructure and Properties of Fiber Laser Welded Girth Joint of Thin-Walled Nanostructured Mo Alloy

Microstructure evolution and enhanced cryogenic toughness of laser welded dissimilar SA645/AISI304L joints via intercritical tempering

Effect of heat input on microstructure and mechanical properties of laser welded joint of Inconel 617 nickel-based superalloy

Microstructure and Softening of Laser-Welded 960 MPa Grade High Strength Steel Joints

Effect of Heat Input on the Microstructures and Mechanical Properties of Laser Welded Ti2AlNb Alloys

Effect of Heat-Input on Microstructure and Toughness of CGHAZ in a High-Nb-Content Microalloyed HSLA Steel.

Study on Laser Welded Heat-Affected Zone in New Ultralow Carbon Bainitic Steel

Effect of Zr-Ti Combined Deoxidation on Toughness of Coarse-Grained Heat-Affected Zone with High Heat Input Welding of Low Carbon High Strength Steels

Pivotal Microstructural Characteristics to Determine the Cryogenic Impact Toughness of Dissimilar Joint Between SA645 and AISI304L Made by Autogenous Fiber Laser Welding

Factors Influencing Notch Toughness of Coarse-grained Heat Affected Zone for 9% Ni Steel

Effect of Heat Input on Microstructure and Mechanical Properties of Laser Welded Medium Mn Steel Joints

Influence of Heat Input on the Changes in the Microstructure and Fracture Behavior of Laser Welded 800mpa Grade High-Strength Low-Alloy Steel

Effects of Ultra-Fast Cooling after Hot Rolling and Lamellarizing on Microstructure and Cryogenic Toughness of 5% Ni Steel