Abstract:Selective laser melting (SLM) technology was employed for the additive manufacturing of Ti-5Al-2.5Sn alpha titanium alloy in this work and the influences of laser energy input on densification behavior, microstructure evolution and mechanical performances of the as-deposited products were investigated. It was found that the relatively high volumetric energy densities (VEDs) of 167-417 J/mm(3) resulted in large quantities of keyhole-induced spherical pores whereas the relatively low VEDs of 51-83 J/mm(3) led to notable lack-of-fusion defects. At the proper VED of 125 J/mm(3), highly densifled products with internal porosity of merely 0.05% were obtained. At the relatively high VEDs of 167-417 J/mm(3), as-built samples presented duplex microstructures composed of acicular alpha' martensites and bulk alpha(M) massive grains. In contrast, overwhelmingly martensitic microstructures were formed at lower VEDs of 51-125 J/mm(3). The martensitic microstructure exhibited a unique hierarchical feature, which could be explained using the theory of athermal martensitic transformation kinetics. With the decrease of VED from 417 J/mm(3), the average size of alpha' needles increased first, then came to its plateau at the VEDs of 167-208 J/mm(3), and decreased again at the VEDs of 51-167 J/mm(3). At the VEDs of 167-417 J/mm(3), the formation of spherical pores and bulk alpha(M) grains resulted in relatively poor tensile properties. At the VEDs of 51-83 J/mm(3), the formation of lack-of-fusion defects masked the enhanced fine-grain strengthening effect provided by the much refined alpha' needles and the decrease in the fraction of bulk alpha(M), thus also leading to very limited tensile properties. At the proper VED of 125 J/mm(3), as-built tensile properties reached to their peak with ultimate tensile strength of 1173 MPa, yield strength of 1061 MPa, and elongation of 7.7%. This can be attributed to the high densification degree, the almost complete vanish of bulk alpha(M) grains, and the moderate size of alpha' needles. (C) 2018 Elsevier B.V. All rights reserved.

Microstructure and Properties of Ti-6Al-4V Fabricated by Low-Power Pulsed Laser Directed Energy Deposition

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

Microstructure and Mechanical Properties of Laser Metal Deposited Ti6Al4V Alloy with Near Equiaxed Β Grain Structure

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Microstructure and Mechanical Properties of Laser Solid Formed Ti-6Al-4V from Blended Elemental Powders

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Microstructural Features of Ti-6Al-4V Manufactured Via High Power Laser Directed Energy Deposition under Low-Cycle Fatigue

Microstructures and Mechanical Properties of Laser Rapid-Formed Ti-6Al-4V Alloy

Additive manufacturing of Ti-6Al-4V alloy by micro-laser metal wire deposition with pulsed wave emission: processability and microstructure formation

Microstructure and mechanical properties of a newly developed Ti-6Al-2Mo-2Sn-2Zr-2Cr-2V alloy fabricated by laser directed energy deposition

Microstructure and deformation behavior of Ti-6Al-4V alloy by high-power laser solid forming

Research on Microstructure and Properties of Ti-6Al-4V Alloys by High Power Laser Solid Forming

Crystal Growth Mechanism and Mechanical Properties of Ti-6Al-4 V Alloy During Selective Laser Melting

Microstructure Characteristics and Failure Mechanisms of Ti-48Al-2Nb-2Cr Titanium Aluminide Intermetallic Alloy Fabricated by Directed Energy Deposition Technique

Densification Behavior, Microstructure Evolution, and Mechanical Performances of Selective Laser Melted Ti-5Al-2.5Sn Α Titanium Alloy: Effect of Laser Energy Input

Effect of boron on the microstructure and mechanical properties of Ti-6Al-4V produced by laser directed energy deposition after heat treatment

Anisotropic Tensile Behavior of Ti-47Al-2Cr-2Nb Alloy Fabricated by Direct Laser Deposition

Hot Tensile Deformation Behavior of Ti-6Al-4V Titanium Alloy Made by Laser Melting Deposition

Tensile Behavior of Ti-6Al-4V Alloy Fabricated by Selective Laser Melting: Effects of Microstructures and As-Built Surface Quality

Mechanical Properties and Microstructure of a High-Power Laser-Welded Ti6Al4V Titanium Alloy