Abstract:While significant work is being carried out to develop materials for enabling high surface charge density triboelectric nanogenerators (TENG), little attention has been paid to the role of electrodes responsible for charge collection. This work reports on the facile synthesis and use of high crystallinity, sp(2)-hybridised laser-induced graphene (LIG) as a high-efficiency electrode for triboelectric nanogenerators (TENGs). Using a conventional 10.6 mu m CO2 laser, the controlled, direct photothermal conversion of dielectric, tribo-negative polyimide (PI) and tribo-positive cellulosic paper into corresponding PI-LIG and paper-LIG, respectively, facilitates a significantly higher electrical output as compared to the commonly utilised adhesive aluminium electrodes. The LIG based paper-PI TENGs showed significantly higher electrical output characteristics with a peak-to-peak voltage of up to-625 V, a current density of-20 mA m(-2) and a transferred charge density of-138 mu Cm-2 with a maximum power output of-2.25 W m(-2), respectively, while the corresponding values for the conventional Al-tape electrode-based paper-PI TENGs were 400 Vp-p, similar to 10 mA m(-2), similar to 85 mu C m(-2) and 0.9 W m(-2), respectively. The mechanically robust LIG electrodes show excellent stability with less than 5.0% variation in output over 12,000 contact cycles. Using Kelvin probe force microscopy (KPFM) measurements, we have measured differences in not only the average surface potentials of the triboelectric surfaces (-0.26 V for pristine PI vs. +0.34 V for paper, which drive the TENG electrical output) but also for the LIG's synthesised from them (-0.08 V for PI-LIG vs. +0.26 V for paper-LIG), suggestive of the role of initial surface chemistry in the formation of LIGs. The enhanced (similar to 150%) power density for LIG based TENGs is ascribed to the lowering of the charge transfer barrier height via the alignment of Fermi levels resulting in higher surface charge on the dielectric surface and the significantly (similar to 6 orders) lower interfacial contact impedance of LIG as compared to adhesive aluminium electrodes. Thus, via the removal of the additional interface between the triboelectric surface and electrode, high-performance metal-free TENGs with excellent prospects for enabling energy harvesting applications can be realised.

Effects of Liquid Metal Particles on Performance of Triboelectric Nanogenerator with Electrospun Polyacrylonitrile Fiber Films

High Performance Triboelectric Nanogenerators with Aligned Carbon Nanotubes.

Influence of Molecular Structure and Material Properties on the Output Performance of Liquid–Solid Triboelectric Nanogenerators

Enhanced Performance Triboelectric Nanogenerators Based on Solid Polymer Electrolytes with Different Concentrations of Cations

Carbon Electrodes Enable Flat Surface PDMS and PA6 Triboelectric Nanogenerators to Achieve Significantly Enhanced Triboelectric Performance

Understanding the Percolation Effect in Triboelectric Nanogenerator with Conductive Intermediate Layer

Liquid metal-based triboelectric nanogenerators for energy harvesting and emerging applications

Effective Interfacial Energy Band Engineering Strategy Toward High-Performance Triboelectric Nanogenerator

MXene based mechanically and electrically enhanced film for triboelectric nanogenerator

High-performance Triboelectric Nanogenerator Based on Electrospun PVDF-graphene Nanosheet Composite Nanofibers for Energy Harvesting

Emulsion Electrospinning of Polytetrafluoroethylene (PTFE) Nanofibrous Membranes for High-Performance Triboelectric Nanogenerators.

Alternate-Layered MXene Composite Film-Based Triboelectric Nanogenerator with Enhanced Electrical Performance

Replacing the Metal Electrodes in Triboelectric Nanogenerators: High-performance Laser-Induced Graphene Electrodes

Sustainable lignin-based electrospun nanofibers for enhanced triboelectric nanogenerators

Enhancing the Output Performance of a Triboelectric Nanogenerator Based on Modified Polyimide and Sandwich-Structured Nanocomposite Film

Significantly Enhanced Performance Of Triboelectric Nanogenerator By Incorporating Batio3 Nanoparticles In Poly(Vinylidene Fluoride) Film

Regulation of nanocrystals structure for high-performance magnetic triboelectric nanogenerator

Improving Relative Permittivity and Suppressing Dielectric Loss of Triboelectric Layers for High-Performance Wearable Electricity Generation.

Enhanced Performance of Triboelectric Nanogenerators and Sensors via Cold Spray Particle Deposition

Enhanced Energy Harvesting Performance of Triboelectric Nanogenerators via Dielectric Property Regulation

Chemical structure-based design of triboelectric materials for high-performance TENGs