Abstract:Electron backscattered diffraction (EBSD) was used to analyze the evolution of microstructure and crystallographic texture during friction stir welding of dissimilar type 2205 duplex stainless steel (DSS) to type S275 low carbon-manganese structural steel. The results of microstructural analyses show that the temperature in the center of stirred zone reached temperatures between Ac1 and Ac3 during welding, resulting in a minor ferrite-to-austenite phase transformation in the S275 steel, and no changes in the fractions of ferrite and austenite in the DSS. Temperatures in the thermomechanically affected and shoulder-affected zones of both materials, in particular toward the root of the weld, did not exceed the Ac1 of S275 steel. The shear generated by the friction between the material and the rotating probe occurred in austenitic/ferritic phase field of the S275 and DSS. In the former, the transformed austenite regions of the microstructure were transformed to acicular ferrite, on cooling, while the dual-phase austenitic/ferritic structure of the latter was retained. Studying the development of crystallographic textures with regard to shear flow lines generated by the probe tool showed the dominance of simple shear components across the whole weld in both materials. The ferrite texture in S275 steel was dominated by D1, D2, E, E¯\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \bar{E} $$\end{document} , and F, where the fraction of acicular ferrite formed on cooling showed a negligible deviation from the texture for the ideal shear texture components of bcc metals. The ferrite texture in DSS was dominated by D1, D2, I, I¯\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \bar{I} $$\end{document} , and F, and that of austenite was dominated by the A, A¯\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \bar{A} $$\end{document}, B, and B¯\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \bar{B} $$\end{document} of the ideal shear texture components for bcc and fcc metals, respectively. While D1, D2, and F components of the ideal shear texture are common between the ferrite in S275 steel and that of dual-phase DSS, the preferential partitioning of strain into the ferrite phase of DSS led to the development of I and I¯\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \bar{I} $$\end{document} components in DSS, as opposed to E and E¯\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \bar{E} $$\end{document} in the S275 steel. The formations of fine and ultrafine equiaxed grains were observed in different regions of both materials that are believed to be due to strain-induced continuous dynamic recrystallization (CDRX) in ferrite of both DSS and S275 steel, and discontinuous dynamic recrystallization (DDRX) in austenite phase of DSS.

Crystallography of Martensite in Friction-Stir-Welded 12cr Heat-Resistant Steel

Crystallographic Analysis of Lath Martensite in a 13Cr-5Ni Steel by Electron Backscattering Diffraction

Grain Structure Development During Friction Stir Welding of Single-Crystal Austenitic Stainless Steel

Crystallographic Characteristics of Phase Transformations in the Field of Medium-Carbon Steels of a Joint Obtained by Rotational Friction Welding

Microstructure and Properties in Friction Stir Weld of 12cr Steel

In Situ Synchrotron X-ray Diffraction Analysis During Post-Weld Heat Treatments of Supermartensitic Stainless Steel Weld Metal

Microstructural Evolution in 304 Austenitic Stainless Steel During Friction Stir Welding

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Microstructure Evolution and Mechanical Properties of Linear Friction Welded S31042 Heat-Resistant Steel

Friction Stir Welding of 1cr11ni2w2mov Martensitic Stainless Steel: Numerical Simulation Based on Coupled Eulerian Lagrangian Approach Supported with Experimental Work

Microstructure Evolution During Friction Stir Welding of 1cr11ni2w2mov Martensitic Stainless Steel at Different Tool Rotation Rates

Identification and quantification of martensite in ferritic-austenitic stainless steels and welds

Crystallographic Texture Evolution and Martensite Transformation in the Strain Hardening Process of a Ferrite-Based Low Density Steel

The microstructure and crystallography of lath martensite with Greninger-Troiano orientation relationship in a Fe-12.8Ni-1.5Si-0.22% C steel

Martensitic Transformation in X12CrMoWVNbN10-1-1 Ferrite Heat-Resistant Steel

Mechanical Properties of Friction Stir Welded 11Cr-Ferritic/martensitic Steel

Effect of microstructure heterogeneity on the mechanical properties of friction stir welded reduced activation ferritic/martensitic steel

Evolution of Microstructure and Crystallographic Texture During Dissimilar Friction Stir Welding of Duplex Stainless Steel to Low Carbon-Manganese Structural Steel

Analysis of crack tip transformation zone in austenitic stainless steel laser-MIG hybrid welded joint

Micromechanical Study of Heterogenous Deformation of Austenitic Stainless Steel Welded Joints at Different Temperatures

Microstructure and mechanical properties of friction stir welded joint of TRIP steel