Abstract:Abstract The reliability and safety of aero-engine are often the decisive factors for the safe and reliable flight of commercial aircraft. Hence, the vibration source location and fault diagnosis of aero-engine are of prime importance to detect faults and carry out fast and effective maintenance in time. However, the vibration signals collected by the sensors arranged on the casing of the aero-engine are generally the mixed signals of the main vibration sources inside the engine, and the components are extremely complicated. Therefore, the vibration source identification is a big challenge for a fault diagnosis and health management of the engine. In order to separate the key vibration sources of rotating machinery such as aero-engine, a Joint Wavelet Transform and Time Synchronous Averaging based algorithm (JWTS) is proposed in this paper. Based on the fact that the fundamental frequency and its harmonic and sub-harmonic components are generally included in the vibration spectrum of shaft fault signal of rotating machinery, wavelet transform and time synchronous averaging algorithm are combined to extract them. The algorithm completes separating the main vibration sources with three steps. First, the source number and fundamental frequency of each source are estimated using the wavelet transform. Second, every source is extracted from each observed signal by the time synchronous averaging method. Time synchronous averaging method can effectively extract a signal of cycle and harmonic rotor components and can suppress noise. Third, the optimal estimation of each source is determined according to signal’s 2-norm. Since the extracted source with a larger energy is closer to the real source, and signal’s 2-norm is a good indicator of the signal energy. Hence, the key vibration sources related to rotary speeds of the engine are obtained separately. The method is verified by synthetic mixed signals first. Three periodic signals of different frequencies are used to simulate the vibration sources of the aeroengine. The fundamental, harmonic and sub-harmonic components of them, as well as Gaussian white noise, are randomly mixed. The results show that the JWTS algorithm can estimate the number of the main sources and can extract each source effectively. Then the method is demonstrated using vibration signals of a real aero-engine. The results indicate that the proposed JWTS method has extracted and located the main sources within the aero-engine, including sources from the low-pressure rotor, high-pressure rotor, combustion chamber and accessory. Therefore, the proposed method provides a new fault diagnosis technology for rotating machinery, especially for a real aero-engine.

An Automatic Abrupt Signal Extraction Method for Fault Diagnosis of Aero-Engines

Feature Extraction Of Impulse Faults For Vibration Signals Based On Sparse Non-Negative Tensor Factorization

Slip Hankel Matrix Series-Based Singular Value Decomposition and Its Application for Fault Feature Extraction

A New Procedure for Extracting Fault Feature of Multi-Frequency Signal from Rotating Machinery

A Novel Strategy for Signal Denoising Using Two-Layer SVD and Its Application to Rub-Impact Fault Diagnosis of Aeroengine

Fault Diagnosis of Demountable Disk-Drum Aero-Engine Rotor Using Customized Multiwavelet Method

Joint Wavelet Transform and Time Synchronous Averaging Source Separation Method and its Application on Aero-Engine

A new method of noise reduction grounded on Hankel matrix and its application in rubbing fault diagnosis

Rotating machinery early fault detection integrating variational mode decomposition and multiscale singular value decomposition

The Fault Feature Extraction of Rolling Bearing Based on EMD and Difference Spectrum of Singular Value

Fault Feature Extraction Method for Rolling Bearings Based on Complete Ensemble Empirical Mode Decomposition with Adaptive Noise and Variational Mode Decomposition

A Pseudo Wavelet System-Based Vibration Signature Extracting Method for Rotating Machinery Fault Detection

A Feature Extraction Approach Of Acoustic Signal Based On Higher-Order Statistics In Rotor Malfunctions

Early fault feature extraction of bearings based on Teager energy operator and optimal VMD

Time-frequency Post-Processing Method Based on Generalized S-transform and Its Application to Aero Engine Rotor System Fault Diagnosis

Diagnosis of Subharmonic Faults of Large Rotating Machinery Based on Emd

Application Of Acoustic Emission Technique In Diagnostics Of Early Rubbing Fault

Wavelet Extraction of Impact Vibration Frequency Component and Fault Analysis for a Twine Spool Aero-Engine

Fusion Fault Diagnosis Approach to Rolling Bearing with Vibrational and Acoustic Emission Signals

Feature Extraction Based on the 3D Spectrum Analysis of Acoustic Signals to Identify Rotor Malfunction

A New Study on Vibration Data Acquisition and Intelligent Fault Diagnostic System for Aero-engine