Abstract:Ti-6Al-4V alloy has the advantages of high strength,good corrosion resistance and good biocompatibility.It is commonly used in the manufacture of porous implant materials,but it has certain restrictions on the forming process of the porous structure.This paper based on forming technology of selective laser melting(SLM),combined with the self-designed topology to optimize the structure of porous mesh,according to the topology optimization results remodeling of the unit structure,three groups of special structure(helical structure,arched bridge structure,thin wall parts and small holes)experiments,analysis and comparison of the microstructure and tensile properties of SLM fabrication Ti-6Al-4V alloy before and after heat treatment.The results show that three kinds of helical structure of SLM molding,in addition to 30 degree spiral structure,the other two are able to complete,which satisfied topological unit structure forming angle(≥45°),30 degree spiral structure can be completed by a small amount of support in the face under scraper.In the arch bridge experiments,can complete the molding of maximum size of arch bridge collapse is φ8 mm,derived the largest suspension length is 0.70 mm,maximum size of arch bridge structure meet the topological unit(8 mm).The wall thickness of 0.10 mm thin wall structure due to laser spot size constraints,its forming size increases 0.05 mm,reduce the porosity of the unit topology of 1mm length size.In the hole forming experiment,minimum diameter is 0.1 mm,meet the optimum production requirements of porous topology minimum holes.The basic mechanical properties of Ti-6Al-4V alloy samples made by SML direct manufactures state and heat treated state could reach the ISO standards and exceed the casting state,but still not as the forging state in ductility.The heat treatment state had a better ductility than that of the direct state,and the direct state have an acicular α'phase martensitic microstructure.When the temperature reached 750 ℃C,a α'phase began to diffuse and decompose,so that white β phase particles were precipitated at the phase boundary.

Selective Laser Melting Process and Mechanical Properties of Cu-Al-Ni-Ti Alloy

Process Optimization, Microstructures and Mechanical Properties of a Cu-based Shape Memory Alloy Fabricated by Selective Laser Melting

Microstructure, Mechanical Properties, and Fatigue Fracture Characteristics of High-Fracture-Resistance Selective Laser Melting Al-Ni-Cu Alloys

Selective Laser Melting of High Strength Al–Cu–Mg Alloys: Processing, Microstructure and Mechanical Properties

Selective Laser Melting of NiTi Alloy with Superior Tensile Property and Shape Memory Effect

Fabrication and Heat Treatment of High Strength Al-Cu-Mg Alloy Processed Using Selective Laser Melting

Study on Properties of SLM-NiTi Shape Memory Alloy under the Same Energy Density

Effect of Process Parameters on the Microstructure and Properties of Cu–Cr–Nb–Ti Alloy Manufactured by Selective Laser Melting

Effect of Energy Density on Mechanical Properties of NiTiCu Shape Memory Alloys Prepared by SLM

Balanced Strength-Ductility Combination and Good Recoverable Strain of Ni50.7Ti49.3 Alloy Fabricated by High Scanning Velocity in Selective Laser Melting

Selective Laser Melting of Cu–Ni–Sn: A Comprehensive Study on the Microstructure, Mechanical Properties, and Deformation Behavior

Effect of Volume Energy Density on Selective Laser Melting Niti Shape Memory Alloys: Microstructural Evolution, Mechanical and Functional Properties

The Ultrahigh Functional Response of CuAlMnNb Shape Memory Alloy by Selective Laser Melting

Enhanced hardness and moderate thermal conductivity of Cu-2.4Ni-0.7Si alloy processed via selective laser melting followed by suitable heat treatment

Altered Phase Transformation Behaviors and Enhanced Bending Shape Memory Property of NiTi Shape Memory Alloy Via Selective Laser Melting

Selective Laser Melting of Al-Cu-Mn-Mg Alloys: Processing and Mechanical Properties

Study on the Process and Properties of Biomedical Ti-6Al-4V Alloy based on Selective Laser Melting

Selective Laser Melting Enabled Additive Manufacturing of Ti-22Al-25Nb Intermetallic: Excellent Combination of Strength and Ductility, and Unique Microstructural Features Associated

Preliminary Investigation on Selective Laser Melting of Ti-5Al-2.5Sn Α-Ti Alloy: from Single Tracks to Bulk 3D Components

Microstructure and Mechanical Property of Ti–5Al–5Mo–5V–3Cr–1Zr Alloy Fabricated by Selective Laser Melting with a Preheated Substrate

Influence of Selective Laser Melting Process Parameters on Microstructure and Properties of a Typical Ni-Based Superalloy