Abstract:In this paper, the depth-sensing indentation (DSI) technique was used to investigate the mechanical properties at the mesoscopic scale of 18Cr–8Ni austenitic stainless steel subjected to low-cycle fatigue loading. For this purpose, several representative analytical approaches for extracting basic mechanical properties, such as the indentation hardness (H), Young's modulus (E), yield strength (σys), strain hardening exponent (n) and plastic energy (Wp), from the indentation load–depth (P–h) curve were introduced. A series of experiments including constant amplitude low-cycle fatigue tests, DSI measurements and transmission electron microscopy (TEM) observations were carried out to obtain the change characteristics of the mechanical properties at the mesoscopic scale of the material as well as their micromechanisms. It is shown that, for the polycrystalline metal investigated, the cyclic plastic deformation remarkably influences its subsequent elastic–plastic response of the small volume material to the indentation process. As the strain amplitudes increases, the mesoscopic mechanical properties (H, E, σys, and n) show increase, while the plastic energy of the indentation (Wp) exhibits a decrease process. Microstructure observations using TEM reveal that, with increasing strain amplitudes, the dislocation substructures in the material tend towards cell formation and the size of dislocation cells tend to progressively decrease. The dependence of the microstructures on the applied strain amplitude is thus responsible for the change characteristics of the mechanical properties at the mesoscopic scale of the material subjected to low-cycle fatigue loading.

Characterizing Deformation Behaviour of an Oxidized High Speed Steel: Effects of Nanoindentation Depth, Friction and Oxide Scale Porosity

Microstructural Study and Residual Stress Measurement of a Hot Rolling Work Roll Material During Isothermal Oxidation

Depth-Sensing Indentation-Based Studies of Surface Mechanical Behavior and Fatigue Damage Evolution of an Austenitic Stainless Steel Subjected to Cyclic Straining

Multi-scale Deformation Behavior Investigation of 18cr–8ni Austenitic Steel Subjected to Low-Cycle Fatigue Loading

Determination of fatigue mesoscopic mechanical properties of an austenitic stainless steel using depth-sensing indentation (DSI) technique

Evolution of Microstructure, Temperature and Stress in A High Speed Steel Work Roll During Hot Rolling: Experiment and Modelling

The Oxidation Behaviors of Indefinite Chill Roll and High Speed Steel Materials

Effects of creep and oxidation on reduced modulus in high-temperature nanoindentation

Revealing Non-Uniform Work-Hardening in a Heterogeneous Structured Steel Using High-Speed Nanoindentation

Theoretical and Experimental Investigation of Thermal and Oxidation Behaviours of a High Speed Steel Work Roll During Hot Rolling

Experimental and Simulation Analysis of Residual Topography Dominated Deformation Mechanism of Nanoindentation: a Case Study of Inconel 625 Superalloy

Effect of Indentation Rate on Deformation Behavior and Mechanical Properties of FeO/Fe is Simulated Based on Molecular Dynamics

Oxide scale characterization of ferritic stainless steel and its deformation and friction in hot rolling

Investigation on nanoindentation and TOF-SIMS applications in the hydrogen and oxygen absorption behavior of Zr-Sn-Nb alloys

Nanoindentation creep deformation behaviour of high nitrogen nickel-free austenitic stainless steel

Modeling Effect of Surface Roughness on Nanoindentation Tests

Nanoindentation Study on the Local Evaluation of Hydrogen-Induced Hardening Performance of Ferrite and Austenite in 2205 Duplex Stainless Steel: Experiment and Finite Element Modeling

Hydrogen Effect on the Deformation Evolution Process in Situ Detected by Nanoindentation Continuous Stiffness Measurement

Synchrotron Study on Load Partitioning Between Ferrite/martensite and Nanoparticles of a 9cr ODS Steel

Hydrogen Effect On The Deformation Behavior Of Austenitic Stainless Steels Investigated By Nanoindentation

Effects of Oxide Scale on the Corrosion and Mechanical Properties for a High Speed Steel and a Graphite Cast Iron