Abstract:When the local heat flux exceeds specified flux limit, tungsten PFC surfaces can be damaged, which is not acceptable for a reliable reactor operations. The divertor PFCs are typically designed for a specific heat flux limit usually assuming an average steady-state heat flux which is typically 5–10 MW/m 2 . However, in addition to steady-state heat flux, fusion reactor divertor PFCs could experience transient heat fluxes such as ELMs and/or other magnetic reconnection events which can deposit large transient heat fluxes onto the divertor PFCs. The transient divertor heat flux could be significantly larger than the steady-state heat flux which could damage the solid PFC surfaces. The divertor heat flux can be subjected to additional complications such as the uncertainties in the the divertor strike point heat flux projection. Moreover, there are additional experimental observations of non-axisymmetric power flux which can occur under non-axisymmetric magnetic perturbations. The liquid lithium (LL) PFCs is more resilient against such transient heat fluxes as they could evaporate LL as needed and the lost LL can be then replenished afterward. In this paper, we analyze a case for a transient divertor heat pulse of 1 MJ in 10 ms for a ITER-size reactor. This is a small perturbation (~ 0.1%) to the expected plasma stored energy compared to the previously analyzed case of 20 MJ heat pulse. Even with this relatively modest heat pulse, the LL surface undergoes ~ 100 °C temperature rise. However, the resulting LL surface heating without rapid cooldown mechanism could lead to excessive LL evaporation continuing well after the transient heat flux resulting in a significant Li injection of ~ 0.6 mol in about a 200 ms period. This amount of Li injection could cause plasma dilution and performance degradation. On the other hand, an active Li injection capability if optimized could prevent the LL surface temperature rise and thus reducing subsequent Li evaporation into the plasma by a factor of 7 compared to the passive LL PFC case. A crucial tool of active Li injection is a rapid response pellet injector which could inject light impurity pellets before the excessive heat flux could reach the divertor plate causing serious damage. A simple pellet ablation model suggests a favorable pellet deposition profile for smaller ~ 0.1 mm radius pellet with ~ 10–20 m/s velocity. Moreover, if it is possible to inject from the private flux region, the pellet injection efficiency into the high heat flux strike point region can be as high as 80% compared to ~ 50% for the injection from outer radius region. The pellet deposition efficiency can be further improved by designing a shell-pellet which can burst when a certain ablation fraction is reached. A possible implementation technique using an inductive pellet injector with a rapid time response of a few msec is proposed here which can be tested in NSTX-U.

Real Time Wall Conditioning with Lithium Powder Injection in Long Pulse H-mode Plasmas in EAST with Tungsten Divertor

Divertor Power Deposition Control and ELM Mitigation with Supersonic Molecular Beam Injection in the EAST Tokamak

Power Balance Investigation in Long-Pulse High-Performance Discharges with ITER-like Tungsten Divertor on EAST

Physics Design of New Lower Tungsten Divertor for Long-Pulse High-Power Operations in EAST

Active Lithium Injection for a Real Time Control of the Divertor Heat Flux for Fusion Devices

I-mode Plasma Confinement Improvement by Real-time Lithium Injection and its Classification on EAST Tokamak

Suppression of tungsten accumulation during ELMy H-mode by lower hybrid wave heating in the EAST tokamak

Tungsten control in nbi-dominant h-mode discharges in east tokamak

Understanding core tungsten (W) transport and control in an improved high-performance fully non-inductive discharge on EAST

Divertor Impurity Seeding with a New Feedback Control Scheme for Maintaining Good Core Confinement in Grassy-Elm H-mode Regime with Tungsten Monoblock Divertor in EAST

Advances in the Long-Pulse Steady-State High Beta H-mode Scenario with Active Controls of Divertor Heat and Particle Fluxes in EAST

Integrated ELM and divertor power flux control using RMPs with low input torque in EAST in support of the ITER research plan

Long-pulse H-mode operation with stored-energy monitoring for detachment feedback control with a new lower tungsten divertor in EAST

Impurity control study of radiative tungsten divertor in EAST tokamak

Enhancement of Tokamak Fusion Test Reactor Performance by Lithium Conditioning

Investigation of Impurity Confinement in Lower Hybrid Wave Heated Plasma on EAST Tokamak

Particle and Power Deposition on Divertor Targets in EAST H-mode Plasmas

Recent EAST Experimental Results and Systems Upgrade in Support of Long-Pulse Steady-State Plasma Operation

Design of EAST lower divertor by considering target erosion and tungsten ion transport during the external impurity seeding

Impact of ELM control techniques on tungsten sputtering in the DIII-D divertor and extrapolations to ITER