Abstract:Spray drying is one of the leading manufacturing methods for active pharmaceutical ingredients (APIs) owing to its rapid, single-step, and cost-effective nature. It also has the capacity to generate microspheres capable of controlled release of APIs including biomolecules and vaccines. However, one of the key challenges of spray-dried formulations especially with poly(lactic-co-glycolic acid) (PLGA)-based controlled-release injectables is burst release, where a significant fraction of the API is released prematurely within a short period of time following administration, leading to detrimental impact on the performance and quality of end products. This study uses a model API, bovine serum albumin (BSA) protein, to identify the sources of burst release that may affect the kinetics and performance of long-acting injectable microsphere formulations. Spray-dried microspheres with various formulations (i.e., variable BSA/PLGA ratios) were characterized in terms of their morphology, particle size, surface area, thermal properties, moisture content, as well as chemical compositions and their distributions to investigate the impact of spray drying on the burst release phenomenon. The results suggest that a relatively high initial release (85%) observed is mainly attributed to the protein distribution close to the particle surface. Morphology analysis provided evidence that the microspheres retained their spherical structure during the burst release phase. X-ray photoelectron spectroscopy, hard X-ray photoelectron spectroscopy, and argon cluster sputtering-assisted time-of-flight secondary ion mass spectrometry analysis suggest an enrichment of PLGA on particle surfaces with buried BSA protein. The statistically significant difference in particle size and surface area between three different formulations may be responsible for an initial variation in release but did not seem to alter the overall burst release profile. Considering the suggested source of burst release, the two-fluid spray-drying method, characterized by a single liquid feed delivering a preprepared emulsion, generated matrix-type microspheres with a surface layer of PLGA, as evidenced by surface analysis. The PLGA surface layer proved to be prone to degradation and pore formation, allowing for faster diffusion of BSA out of the microspheres, resulting in a burst release. Increasing the polymer concentration did not seem to halt this process.

Smart Release-Control of Microencapsulated Ingredients from Milk Protein Tablets Using Spray Drying and Heating

Pre-gelation Assisted Spray Drying of Whey Protein Isolates (WPI) for Microencapsulation and Controlled Release

Controlled Release of Caffeine from Tablets of Spray-Dried Casein Gels

Preparation of Sustained Release Capsules by Electrostatic Dry Powder Coating, Using Traditional Dip Coating As Reference

Microencapsulation of Pepsin in the Spray-Dried WPI (whey Protein Isolates) Matrices for Controlled Release

Fabrication of Novel Casein Gel with Controlled Release Property Via Acidification, Spray Drying and Tableting Approach.

The in-vitro digestion behaviors of milk proteins acting as wall materials in spray-dried microparticles: Effects on the release of loaded blueberry anthocyanins

On Designing Particulate Carriers for Encapsulation and Controlled Release Applications

Pulsatile protein release from a laminated device comprising of polyanhydrides and pH-sensitive complexes

Design of Polymeric Microparticles for Ph-Responsive and Time-Sustained Drug Release

On spray drying of uniform silica-based microencapsulates for controlled release

One-pot Synthesis and Encapsulation of Hydrophilic Drug in Uniform Microparticles for Controlled Release

Improvement of protein loading and modulation of protein release from poly(lactide-co-glycolide) microspheres by complexation of proteins with polyanions.

Fabrication and Characterization of Whey Protein—Citrate Mung Bean Starch—Capsaicin Microcapsules by Spray Drying with Improved Stability and Solubility

Spray drying of monodispersed microencapsulates: implications of formulation and process parameters on microstructural properties and controlled release functionality.

Spray Drying of Hydrocolloids: Case Study for Phresponsive and Time-Sustained Release

Design And Characterization Of Controlled-Release Edible Packaging Films Prepared With Synergistic Whey-Protein Polysaccharide Complexes

Fabrication of Drug-Loaded Biodegradable Microcapsules for Controlled Release by Combination of Solvent Evaporation and Layer-by-layer Self-Assembly

Preparation and characterization of microcapsules based on biodegradable polymers: pectin/casein complex for controlled drug release systems

New Insights on the Burst Release Kinetics of Spray-Dried PLGA Microspheres

Polymer-Based Sustained-Release Dosage Forms for Protein Drugs, Challenges, and Recent Advances