Abstract:Numerous processes have been applied to refine the microstructure and the precipitation of carbides in ultra-high carbon steel (UHCS). However, the evolution of microstructure and carbide precipitation in UHCSs during the hot deformation compression process remains poorly understood. The present study addresses this issue by applying hot deformation compression to Fe-C-Cr-V-Mo UHCS specimens at temperatures of 950–1150 °C under strain rates of 0.01–5 s−1, and evaluating the resulting flow curves and microstructures of the specimens after cooling in air. High deformation temperature and high strain rate conditions are observed to generate flow curve stress peaks, which result in dynamic recrystallization. In addition, dislocation cell formation and substructure are observed at deformation temperatures of 950 °C and 1050 °C, respectively, under a strain rate of 1 s−1. The recrystallized grain structure fraction is found to be positively correlated with the deformation temperature at strain rates less than 5 s−1, and a fully recrystallized grain structure is not obtained at a strain rate of 5 s−1 even at a temperature of 1150 °C. Moreover, the concentration of primary M7C3 carbides is observed to decrease with increasing deformation temperature, and fine precipitated M23C6 particles are observed in the matrix during hot deformation. An increased concentration of precipitated M23C6 particles is also observed in the specimen microstructure at a deformation temperature of 1150 °C and a strain rate of 5 s−1. The recrystallization process is also observed to vary according to M23C6 particle size, where large M23C6 particles are observed to stimulate the formation of recrystallization nuclei and fine M23C6 particles delay or hinder the recrystallization process.

Study on Dynamic Recrystallization Behaviors in a Hot-Deformed FB2 Ultra-supercritical Rotor Steel

Hot Deformation Behavior and Thermal Processing Map of 630°C Ultra-Supercritical Rotor Steel

Study on dynamic recrystallization of ultra-high strength 22MnB5 steel during hot rolling

Studies on Hot Deformation Behavior and Dynamic Recrystallization in a High Al Ferritic Low-Density Steel

Research on Dynamic Recrystallization Behavior of 30Cr2Ni4MoV Rotor Steel

Constitutive Modeling and Dynamic Softening Mechanism During Hot Deformation of an Ultra-Pure 17%cr Ferritic Stainless Steel Stabilized with Nb

Effect of Grain Size and Compression Direction on the Hot Deformation Characteristics of High-Cr Ultra-Super-Critical Rotor Steel with Columnar Grains

Research on hot deformation, dynamic recrystallization and numerical simulation of Fe–28Mn–10Al–1.5C–0.6V steel

Stress-strain behavior and microstructural evolution of ultra-high carbon Fe-C-Cr-V-Mo steel subjected to hot deformation

Study on Hot‐Compressive Deformation Behavior and Microstructure Evolution of 12Cr10Co3MoWVNbNB Martensitic Steel

Microstructure simulation and experiment investigation of dynamic recrystallization for ultra high strength steel during hot forging

Study on the dynamic recrystallization mechanisms of GH5188 superalloy during hot compression deformation

Kinetics and microstructure evolution of dynamic recrystallization of medium-Mn steel during hot working

Research on the Dynamic Recrystallization Behavior of 30cr2ni4mov LP Rotor Steel under Multi-Pass Deformation

Characteristic and Mechanism of Dynamic Recrystallization in a Newly Developed Fe-Cr-Ni-Al-Nb Superalloy During Hot Deformation

Dynamic Recrystallization Behavior of Fe–20Cr–30Ni–0.6Nb–2Al–Mo Alloy

Dynamic Recrystallization Behavior of Low‐Carbon Steel during the Flexible Rolling Process: Modeling and Characterization

Study on Hot Deformation Behavior of an Ultra Purified 21%cr Ferritic Stainless Steel

Static Recrystallization Behavior of Low-Carbon Nb-V-Microalloyed Forging Steel

Study on the hot deformation behavior and microstructure evolution of as-forged GH3625 alloy

Mechanism of dynamic recrystallization of a FeCrAl alloy during hot compression