Abstract:AbstractThe search for suitable friction materials for high-speed train is an attractive but difficult problem. In recent years, a variety of different novel friction materials were fabricated to meet the aims of high loads and speeds under ambient environment. Carbon fiber-reinforced carbon composites (C/C), carbon fiber-reinforced silicon carbide composites (C/C-SiC) and metallic composites fabricated by powder metallurgy are three excellent materials among them. Here a comparison of these three different materials working as brake pads, coupled with high-density C/C-SiC brake disk, was described. All the experiments were conducted using the same procedure with increasing initial braking speed (the rotation speed of brake disk at the beginning of braking process) from 30 to 59 m/s and constant load of 1.25 MPa, simulating the real working condition of high-speed train. The coefficient of friction (COF) and wear rates of three materials were compared and analyzed. During experiments, the COF of metallic and C/C pads remains nearly constant at 0.31 and 0.22, respectively, with increasing braking speed, while that of C/C-SiC exhibits a parabola. These different trends of COF may be attributed to the distinctive forming processes of friction film on the top of contact surfaces. Meanwhile, the wear rates of metallic composites increase rapidly from 683 to 1803 mm3/MJ with initial braking speed, while C/C-SiC presents the highest wear loss of 1887 mm3/MJ at 49 m/s and lowest value of 315 mm3/MJ at 59 m/s. Interestingly, the wear rate of C/C composites, due to the appropriate bonding strength of matrix/fiber and relatively high shear stress, decreases from 3698 to 903 mm3/MJ with increasing initial braking speed, which does not consist with pre-existing paper. Thus, metallic pads presented the lowest wear rates at lower speed (<49 m/s) but the highest at high speed, while C/C-SiC composite pads showed the greatest wear resistance at high speed. This investigation of three different friction materials will enhance our understanding of these friction materials and benefit the selection and safe application of high-speed train friction materials.

Tribological Properties and Thermal-Stress Analysis of C/C-SiC Composites During Braking

Coupled thermal-structural analysis of an axle mounted C/C-SiC brake disc for high-speed trains

Fading behavior and wear mechanisms of C/C–SiC brake disc during cyclic braking

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Mechanical and tribological properties of C/C–SiC ceramic composites with different preforms

Comparison of Friction and Wear Behavior Between C/C, C/C-SiC and Metallic Composite Materials

Simulation-based microstructural analysis of thermal–mechanical fatigue behavior in SiCp/A356 composites for brake disc applications

Effect of graphitization on microstructure and tribological properties of C/SiC composites prepared by reactive melt infiltration

Comparison of the Braking Behavior Among Cast Steel, Carbon/Carbon (C/C) and Carbon/Carbon-Silicon Carbide (C/C-SiC) Materials Mated with Copper-Based Composites

Friction and Wear Mechanics of Fe-Based PM Pad Paired with Carbon Fiber-Reinforced Silicon Carbide (C/C-SiC) Disk Under High-Speed Braking

Friction And Wear Properties Of Aluminum Matrix Composites And Its Application

Effect of heat treatment on the tribological behavior of 2D carbon/carbon composites

Effects of Sintering Temperature on Bending Property of C-F/Sic Brake Material

Microstructures and properties of C/C–SiC composites derived from different gaseous carbon matrix precursors

Friction and Wear Properties of Pitch/resin Densified Carbon Carbon Composites Used for Airbrakes

Simulation of the Friction Temperature Field for Disc Brake

The structural effect of SiC form ceramic on the compressive strength and thermal expansion properties of Cu–SiC composites

Static friction properties of carbon/carbon composites

Effects of Sintering Temperature on Bending Property of C<sub>f</sub>/SiC Brake Material

Tribological behavior and mechanism of h-BN modified copper metal matrix composites paired with C/C–SiC

Effects of carbon fiber dispersion on bending property of Cf/SiC brake materials