Abstract:In order to reveal the relationship between microstructure inhomogeneity and mechanical anisotropy, the Al–Cu–Li alloy 100 mm thick plate for aerospace was evaluated. The grain structure, crystallographic texture, phase structure and fractography of different thickness positions and directions were observed by optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). The in-plane and through-thickness anisotropy were characterized by tensile properties, fracture toughness and hardness tests. The results demonstrate a greater in-plane anisotropy in yield strength at the same thickness position of the plate. The Brass texture component increases successively at T, T/4, and T/2 positions, while the Cu texture component exhibits minimal variation. The in-plane anisotropy mainly arises from the Brass texture. Through-thickness anisotropy in the same direction is primarily influenced by the diameter, number density, and volume fraction of the T1 strengthening phase. The average diameter and number density of the primary strengthening phase T1 within grains are highest at the T/2 position and lowest at the T position. The plate contains unrecrystallized, elongated pancake-like grains along the rolling direction. Fracture toughness tests conducted in the L-T and T-L directions predominantly reveal dimple-type transgranular shear fractures, while the S-L direction exhibits intergranular fracture as the primary characteristic. The crack divider delamination toughening mechanism is the main contributor to higher fracture toughness values in the L-T and T-L directions compared to those in the S-L direction. The results reveal the corresponding relationship between the microstructure inhomogeneity and the mechanical anisotropy of Al–Li alloy ultra-thick plates, and provide ideas for the adjustment of process parameters during processing deformation and the regulation of microstructure during heat treatment of large-scale Al–Li alloy thick plates, which has engineering application reference value.

In-plane Elastic Anisotropic Constants (ieacs) Measurement of Rolling Aluminum Plate at Different Depth Using Ultrasonic LCR Wave

Mechanical Properties and Acoustic Emission Characteristics of Anchored Structure Plane with Different JRC under Direct Shear Test

Study on Measurement Method of Interior Stress Distributions in Engineering Rolled-Plates

Plane Stress Measurement of Orthotropic Materials Using Critically Refracted Longitudinal Waves

Inline Measurement of Acoustoelastic Coefficient in Conductive Sheet Material With Electromagnetic Loading System

Angular Measurement of Acoustic Reflection Coefficients by the Inversion of V(z, T) Data with High Frequency Time-Resolved Acoustic Microscopy

Effect of microstructural inhomogeneity on mechanical anisotropy of Al–Cu–Li alloy plate

Predicting the in-plane mechanical anisotropy of 7085 aluminum alloys through crystal plasticity simulations and machine learning

Ultrasonic Evaluation of Acoustoelastic Parameters in Aluminum

A method for determining r-value of aluminum sheets with the Portevin-Le Chatelier effect

Measurement of Elastic Constant Matrix of Carbon Fiber Composites With an Ultrasonic 2D-Array Transducer

Characterization of Portevin–Le Chatelier Effect in Aluminum Alloy AA5052 under Strain-Controlled Tensile Test Via Digital Image Correlation and Acoustic Emission

Correlation Between Microstructural Heterogeneity and Anisotropy of Mechanical Properties of Laser Powder Bed Fused CoCrFeMnNi High Entropy Alloy

Acoustic anisotropy and localization of plastic deformation in aluminum alloys

Non-destructive evaluation of non-uniform stress fields and subsurface stress gradients using ultrasonic waves

Ultrasonic Measurement of Residual Stress in Pre-stretched Aluminum Alloy Plate by Using Ultrasonic and Its Verification

The Strain Rate and Density Dependence of the Mechanical Properties of Closed-Cell Aluminum Foam

Anisotropic plastic flow of low/medium carbon steel plates in different loading conditions: characterization of the r- value

On high‐cycle fatigue anisotropy of an aluminum alloy super‐thick plate

Identification of forming performance parameters for 6016 aluminum alloy sheet under different strain paths via digital image correlation technology

Anisotropy Study of Thin Metallic Sheets with Strain Measurement of Digital Speckle Correlation