Abstract:Tristructural-isotropic (TRISO) fuel particles have long been widely used in high temperature gas-cooled reactors (HTGR), where their high temperature mechanical integrity and ability to retain fission products even in the accident conditions are the critical safety issues. In the present work, TRISO particles were subjected to ultra-high temperature thermal treatments at 1900, 2000, and 2200 degrees C, respectively, which were much higher than the projected accident temperature (1620 degrees C). Phase compositions and microstructures of the samples before and after thermal treatments were studied by X-ray diffraction (XRD), Raman spectroscopy, and Scanning Electron Microscopy (SEM). Nano hardness and Young's modulus of the SiC layer in TRISO particles were studied by nano indentation technique, and crushing strength of the TRISO particles was evaluated by mechanical crush tests. The results show that, there were no obvious temperature effects on phase composition and microstructure, except for SiC layer in the sample thermal treated at 2200 degrees C, in which many pores caused by SiC decomposition were observed. The nano hardness and Young's modulus values of SiC layer in the as-received and thermally treated TRISO particles were similar within the experimental error. On the other hand, the crushing strength of the thermally treated TRISO particles decreased greatly as compared with the as-received particles, but the crack propagation mode changed from through-the-particle to deflection inside the buffer PyC layer or between buffer PyC and inner PyC (IPyC) layers. The change of crack propagation mode could probably due to the shrinkage of PyC layers due to anisotropy at high temperature and ordering of graphitization of IPyC layers, which probably weakened the interfacial bonding between the IPyC and the buffer PyC layers. The results of this study provide a database reference for the performance of TRISO particles under ultra-high temperature operation and even accident conditions. (C) 2022 Elsevier B.V. All rights reserved.

Synchrotron Phase-Contrast CT to Segment the Structure Boundaries of a TRISO-coated Particle

Three-Dimensional Measurement of TRISO Coated Particle Using Micro Computed Tomography

Failure Fraction Calculation of the TRISO-Coated Particle Using X-Ray Computed Tomography

3D Nondestructive Visualization and Evaluation of TRISO Particles Distribution in HTGR Fuel Pebbles Using Cone-Beam Computed Tomography

Stress Analysis of Aspherical TRISO-coated Particle with X-ray Computed Tomography

Uniformity Assessment of TRISO Fuel Particle Distribution in Spherical HTGR Fuel Element Using Voronoi Tessellation and Delaunay Triangulation

The Study of Irradiation-Induced Failure Behavior for the TRISO-coated Fuel Particle in HTGR

Layer thickness measurement of the TRISO-coated particle based on U-Net

Simulation of the Digital Image Processing Algorithm for the Coating Thickness Automatic Measurement of the TRISO-coated Fuel Particle

Algorithms for TRISO Fuel Identification Based on X-ray CT Validated on Tungsten-Carbide Compacts

Irradiation-Thermal-Mechanical Coupling Behaviors of a Typical TRISO/SiC Fuel Element Based on Actual Distribution

Evaluation of Thermal Conductivity of the Constituent Layers in TRISO Particles Using Raman Spectroscopy

Effect of Ultra-High Temperature Treatment on Microstructures and Mechanical Properties of TRISO Particles

Sensitivity study on triso fuel failure probability evaluation for htgr

Improved measurement of local thermal conductivities of coatings by the steady-state Raman spectroscopy method: A case study in TRISO particles

An Improved Design of TRISO Particle with Porous SiC Inner Layer by Fluidized Bed-Chemical Vapor Deposition

Phase Field Modeling of Irradiation-induced Shrinkage Fracture in TRISO Fuel Particle

Thickness measurement of coatings for HTGR coated fuel particles

Analysis of micro-defect-induced cracking in the IPyC layer of TRISO particle with the XFEM

Precise Strain Profile Measurement As a Function of Depth in Thermal Barrier Coatings Using High Energy Synchrotron X-rays

Comparison of neutronic aspects in high‐temperature gas‐cooled reactor using ZrC and SiC Triso particle with 50 and 100 MWt power