Abstract:ZrO 2 ceramics are commonly known as 'hard and brittle' materials due to their exceptional properties, such as high hardness, heat resistance, chemical stability, and low thermal conductivity. However, the hole processing technique for ZrO 2 ceramics often results in significant tool wear and compromises the quality of the holes. This study investigates the removal mechanism of ZrO 2 ceramic materials by using carbide tools, diamond-coated carbide tools, and micro-sintered tools. It also analyzes the impact of processing parameters on the wear mechanism of different tools and the quality of hole processing in ZrO 2 ceramics. The findings revealed that at high spindle speed (8000 r/min) and low feed rate (1 mm/min), the diamond coating on the rake surface of the diamond-coated carbide tool tends to peel off, leading to the formation of sharp edges on the flank surface. This phenomenon results in a reduction in thrust forces. Moreover, it is observed that as the number of hole machining operations increases, the peeling of the diamond coating on the tool flank becomes more severe. The increase in feed rate causes the diamond coating peeling area on the rake face of the tool to expand toward the chisel edge and even reach the thinned edge area near the chisel edge. When the feed rate of carbide tools increases, the wear degree of the chisel edge gradually increases, while the wear degree of the main cutting edge corner position gradually decreases. At low spindle speeds, the main cutting edge breaks and the cutter head is also damaged and deformed. The main wear mechanisms of micro-sintered tools involve shedding, fragmentation, wear, and adhesion of diamond abrasive grains. The bottom surface of the tool tends to accumulate a significant amount of flaky adhesion, which dulls the tool and increases thrust force. In contrast to carbide tools, diamond-coated carbide tools offer improved hole exit quality. However, micro-sintered tools often exhibit large volumes of flaking at the hole exits, resulting in shell-like stripes on the peeled surface.

Hole Quality Control in Underwater Drilling of Yttria-Stabilized Zirconia Using a Picosecond Laser

An investigation on the hole quality during picosecond laser helical drilling of stainless steel 304

Development of a Quantitative Method for the Characterization of Hole Quality During Laser Trepan Drilling of High-Temperature Alloy

Hole Quality and Thermal Defects in Drilled CFRP by Nanosecond Pulsed Laser

Effect of dopant concentration on femtosecond pulsed laser irradiation of yttria-stabilized zirconia for generating nanopores

Investigation on Thermal Barrier Coating Damages for Ultrafast Laser Drilling of Cooling Holes

Experimental investigation and optimization of modification during coaxial waterjet-assisted femtosecond laser drilling

Experimental research on ultrasound-assisted underwater femtosecond laser drilling

Triple Rings Trepanning Technology for Holes Ablated Using Nanosecond Pulse Laser in Al2O3 Ceramics Substrate

Ultrafast Laser Drilling of Crack-free, Debris-free and Heat Affected Zone (Haz)-Free Blind Holes in Al2O3 with Flat Bottom and Reduced Taper Angles

High-quality Rapid Laser Drilling of Transparent Hard Materials

Experimental Investigation of Water Jet-Guided Laser Micro-Hole Drilling of Cf/SiC Composites

A Comparison in laser precision drilling of stainless steel 304 with nanosecond and picosecond laser pulses

Research on the mechanism of laser drilling alumina ceramics in shallow water

Polarization-dependent, Beam Reflection-Regulated Hole Shaping Dynamics Visualized by In-Situ Imaging of Ultrafast Laser Drilling Process

Chemical and Structural Origin of Hole States in Yttria-Stabilized Zirconia

A comprehensive study on water jet guided laser micro hole drilling of an aerospace alloy

Comparative study of tool wear mechanisms in drilling ZrO2 ceramics using various tool types

Temperature field simulation and optimization of processing parameters for laser-assisted machining of 3Y-TZP ceramics

Optimizing Hole Shape and Improving Surface Quality of Inconel 718 Alloy by High-Temperature Chemical Assisted Laser Processing

Molecular dynamics-guided quality improvement in the femtosecond laser percussion drilling of microholes using a two-stage pulse energy process