Abstract:SiCp/Al composites have been widely used in many fields due to their excellent mechanical properties. However, the addition of reinforced phase SiC particles makes the overall properties of the composites hard and brittle, which brings great challenges to milling. Ultrasonic vibration-assisted processing technology has great advantages in processing hard and brittle materials. However, the process of rupture of SiC particles cannot be effectively observed during the test processing, and a large number of tests increase the cost of the test. The combination of finite element analysis and experiment was used to study the machining performance of High-volume fraction SiCp/Al composites in longitudinal-torsional ultrasonic-assisted milling (LTUAM), and its feasibility was evaluated by comparing with conventional Milling (CM). By analyzing the trajectories of cutting edges in ultrasonic-assisted milling, It was found that ultrasonic frequency determines the time of periodic contact-separation between chisel edge and workpiece, and ultrasonic amplitude determines the maximum distance of contact-separation. Using ABAQUS finite element software, a polygon SiC particles model with a high-volume fraction was established to investigate the SiC particles crushing process under different ultrasonic-assisted milling conditions. The results showed that high-frequency ultrasonic-assisted milling could soften SiCp/Al composites, and the structural integrity of silicon carbide particles could be better maintained under appropriate ultrasonic amplitudes, reducing the probability of fragmentation. The removal mode was mainly plastic removal or crushing into small particles. The surface roughness value and milling force were reduced, improving the surface quality of the processed composite material. The conclusions of the milling test were basically consistent with the simulation results, which prove the correctness and feasibility of the simulation results.

Particle Distribution and Mechanical Properties of Nano-SiCP/Al-Cu Composites

Effects of nanoparticles on the solution treatment and mechanical properties of nano-SiCp/Al-Cu composites

Study of Hot-press Sintering Process of Nanometer Cu-Al_2O_3 Composite

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: Effects of SiC nanoparticles addition and heat treatment

Finite Element and Experimental Analysis of Ultrasonic Vibration Milling of High-Volume Fraction SiCp/Al Composites

Effect of Ultrasonic Vibration Tensile on the Mechanical Properties of High-Volume Fraction SiCp/Al Composite

Enhanced Mechanical Behavior and Fabrication of Silicon Carbide Particles Covered by In-Situ Carbon Nanotube Reinforced 6061 Aluminum Matrix Composites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Study on the processing performance of 60% SiCp/Al composite materials assisted by longitudinal and torsional ultrasonic vibration milling

Investigation of SiC Nanoparticle Size and Distribution Effects on Microstructure and Mechanical Properties of Al/SiC/Cu Composite during the FSSW Process: Experimental and Simulation

Microstructure And Mechanical Properties Of Al-Sic Nanocomposites Synthesized By Surface-Modified Aluminium Powder

Preparation, microstructure and tensile properties of two dimensional MXene reinforced copper matrix composites

Untrasonic-Assisted Fabrication of SiC Nanoparticles Reinforced Aluminum Matrix Composites

Influence of micron and nano SiC<sub>p</sub> on microstructure evolution and mechanical properties of laser metal deposition AlSi10Mg alloy

Fabrication of Nano-Sic_p/al Composite by High Energy Ball Milling

Microstructure and Mechanical Properties of Cu-CoatedCarbon-Nanotubes-Reinforced Aluminum Matrix Composites Fabricated by Ultrasonic-Assisted Casting

Microstructure Evolution and Wear Characterization of Cnts/Al-Cu-Mg-Si Nanocomposites Manufactured Using Semi-Solid Stir Casting

Experimental and FEM study of surface formation and deformation mechanism of SiCp/Al composites in laser-ultrasonic vibration assisted turning

Ultrasonic assisted fabrication of particle reinforced bonds joining aluminum metal matrix composites

Effects of High Intensity Ultrasonic Processing on Preparation of SiC Nano-Particles Reinforced Magnesium Matrix Composite