Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

Neutronics and Thermo-Hydraulic Analysis of Water-Cooled Blanket Based on Pwr and Scwr Water Conditions for Cfetr

Neutronics Comparison Analysis of the Water Cooled Ceramics Breeding Blanket for CFETR

An Approach to Increase the Fusion Tritium Breeding Ratio Using Temperature Field Balance Based on Water-Cooled Ceramic Blanket

Development of neutronic-thermal hydraulic-mechanic-coupled platform for WCCB blanket design for CFETR

Optimal Design for Helium Cooled Solid Breeder Blanket of CFETR

Investigation on the Tritium Self-Sufficiency and Neutron Shielding Based on a Water-Cooled Blanket for CFETR at 1.5 GW

Neutronics Effects of Homogeneous Model on Solid Breeder Blanket of CFETR

Study on Neutronics and Thermo-hydraulics for Mixed Pebble Bed Blanket of Fusion Reactor

Analysis and Optimization of Cooling Channels in ITER Blanket Module

Neutronics Design Optimization on Cross Cooled Solid Blanket of Fusion Reactor

Technical Issues for the Fabrication of A Cn-Hccb-Tbm Based on Rafm Steel Clf-1

Neutronic Analysis of a Thorium-Uranium Fueled Water Cooled Fusion-Fission Hybrid Blanket

Study on the Influencing Factors of Temperature Field Based on PWR Water-Cooled Blanket for DEMO Reactor

Interface design of the blanket system for CFETR

Tritium Transport Modeling and Analysis for HCCB Blanket of CFETR

Preliminary Design of A Solid Particulate Cooled Blanket for the Steady-State Tokamak Reactor (Sstr)

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Preliminary Neutronics Analyses of China Dual-Functional Lithium-Lead (DFLL) Test Blanket Module for CFETR

Development of thermo-physical property database and code of fusion materials for CFETR blankets

Exploratory tritium breeding performance study on a water cooled lead ceramic breeder blanket for EU DEMO using Serpent-2

Studies on Flibe Blanket Designs in Helical Reactor FFHR