Abstract:Flibe blanket is one of the advanced liquid blankets for fusion DEMO reactor and its conceptual design is in progress to date. Although the blanket using molten salt, Flibe, has many strong points such that a simple and compact blanket can be realized because Flibe acts as both coolant and tritium breeder, there are still several issues to be solved. One of the key issues is heat transfer enhancement in flowing fluid with high Pr number such as Flibe. Previous design activity indicated that conventional Flibe composed of 66 % of LiF and 34 % of BeF2 has too high melting point of 459 deg. C to design the blanket because of small temperature window between allowable temperature of structural material (about 550 deg. C for the case of reduced activation ferritic steel) and the melting point, and it is necessary for extensional design to reduce the melting point of Flibe by changing its composition, i.e., increasing the ratio of BeF2. This operation, however, increases Pr number of the resultant Flibe, and makes the already low heat transfer performance lower. Spherepacked pipe (SPP) has been proposed as a measure to enhance the heat transfer performance and as a cooling channel of the first wall of the Flibe blanket. There are many parameters such as the channel width, diameter of the packed sphere and so on, and they have to be optimized for realization of the blanket. In this study, heat transfer experiment using silicon oils as high Pr number fluid was conducted to clarify thermofluid characteristics of the SPP for the silicon oils with Pr number up to 100. Besides, in preparation for high heat load removal experiment using Tohoku-NIFS Thermal loop (TNT loop) with Filbe simulant as coolant, the loop was improved. Bypass operation of a heat exchanger piping and maintenance and repair of a pumping system were done in order to increase coolant flow rate. Parameters of the heat transfer experiment were Pr number (Pr=25 or 100), ratio of diameter of spheres to that of a circular pipe (D/d=2 or 3), material of the spheres (brass, SUS or polypropylene) and Re number (ReD=2008,000). Fig. 1 shows a test section. Heat deposition of 45140 kW/m2 was given between two electrodes by applying direct current. Because wall temperature of the pipe depended on location of the pipe, a total of 60 thermocouples were installed to estimate more accurate averaged wall temperature. Averaged heat transfer rate was calculated by using averaged inner wall temperature estimated from temperature of the thermocouples and bulk temperature of flowing coolant. Figs. 2 and 3 shows averaged Nusselt number for the case of Pr=100, D/d=2 and Pr=100, D/d=3, respectively. In these figures, solid lines correspond to a correlation data obtained from previous studies by using experimental data of 5.1<Pr<31, 820<ReD<33500, and dashed lines are extrapolated from this correlation. It is found from these figures that Nusselt number obtained from the experiment is quite different from the correlation. The previously obtained correlation has a relation of Nu�Pr, but for high Pr number fluid, this relation is considered not to be applicable. To derive the brand-new heat transfer correlation for high Pr number fluid, additional heat transfer experiment should be necessary and that using silicon oil with Pr=200 is scheduled.

Study on the Influencing Factors of Temperature Field Based on PWR Water-Cooled Blanket for DEMO Reactor

Exploratory tritium breeding performance study on a water cooled lead ceramic breeder blanket for EU DEMO using Serpent-2

Development of water-cooled cylindrical blanket in JA DEMO

Analysis and Optimization of Cooling Channels in ITER Blanket Module

Neutronics Comparison Analysis of the Water Cooled Ceramics Breeding Blanket for CFETR

An Approach to Increase the Fusion Tritium Breeding Ratio Using Temperature Field Balance Based on Water-Cooled Ceramic Blanket

Optimal Design for Helium Cooled Solid Breeder Blanket of CFETR

Thermohydraulic Analysis of Accident Scenarios of a Fusion DEMO Reactor Based on Water-Cooled Ceramic Breeder Blanket: Analysis of LOCAs and LOVA

Tritium Transport Modeling and Analysis for HCCB Blanket of CFETR

Development of neutronic-thermal hydraulic-mechanic-coupled platform for WCCB blanket design for CFETR

Neutronics Design Optimization on Cross Cooled Solid Blanket of Fusion Reactor

Neutronics Analyzation of Helium Cooled Solid Breeder Blanket in a Fusion Reactor

Investigation on the Tritium Self-Sufficiency and Neutron Shielding Based on a Water-Cooled Blanket for CFETR at 1.5 GW

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Current Design And R&D Progress Of The Chinese Helium Cooled Ceramic Breeder Test Blanket System

Interface design of the blanket system for CFETR

Heat Removal Demo-research for Flibe Blanket Development

Neutronic Analysis of a Thorium-Uranium Fueled Water Cooled Fusion-Fission Hybrid Blanket

Integrated design of breeding blanket and ancillary systems related to the use of helium or water as a coolant and impact on the overall plant design

Study on Neutronics and Thermo-hydraulics for Mixed Pebble Bed Blanket of Fusion Reactor

Neutronics Effects of Homogeneous Model on Solid Breeder Blanket of CFETR