Abstract:Multichips paralleled insulated gate bipolar transistor (IGBT) power modules are widely employed in industrial and automotive power conversion systems. The asymmetry of the circuit topology and the differences in chip characteristics are the main reasons for the unbalanced current distribution among parallel chips, leading to excessive electrical stress in power modules, which in turn forces the power modules to operate at a reduced rated current. Additionally, the unbalanced current distribution inevitably results in different chip losses, which are further amplified under high current loading conditions, causing some chips to be overheated, and significantly reducing the reliability. Optimizing the circuit topology is a common method to improve current distribution, but global changes often entail higher costs and longer development cycles. Moreover, the electrical parasitic of the fast recovery diodes (FRD) chip branches are not given sufficient attention in circuit topology research. Under rectification and blocked conditions in electric vehicles, FRDs often become the bottleneck for lifespan due to excessively high junction temperatures. Therefore, this article conducts a comparative analysis of the circuit parasitic in IGBT and FRD loops with several typical layouts, without changing the substrate and chip dimensions, and proposes a current sharing slot structure design to balance the parasitic parameters. Compared with the direct bonded copper (DBC) layout of the typical EconoDUAL power module, the optimized module reduces the current imbalance of FRD from 45.5% to 11.6% and the switching loss can be reduced by 8.6%. By adopting the current sharing groove, the parasitic parameter distribution can be further improved while maintaining a fixed DBC layout, considering the IGBT and FRD branches in concert. Finally, the steady-state and transient current sharing characteristics were verified under constant current and inverter conditions. Under constant current conditions, the temperature difference of FRD in the upper and lower parallel layout modules was reduced by 16.7 °C, and the junction temperature of IGBT was significantly lowered. Under inverter conditions, the highest junction temperature of the columnar layout modules could be reduced by 10 °C, and the temperature difference of FRD decreased by 62%. This article significantly optimizes the current imbalance issue through layout design, reduces the thermal equilibrium difference of the module under application conditions, and is conducive to improving the output capacity and fatigue life of the module, providing a solution for the design of power modules with high junction temperature operation capability and high-reliability.

Comparative Evaluation of Kelvin Connection for Current Sharing of Multi-Chip Power Modules

Influence of Kelvin Connection on Current Dispatching in Multichip Power Module: Mechanism Modeling and Comparative Evaluation

Layout-Dominated Dynamic Current Imbalance in Multichip Power Module: Mechanism Modeling and Comparative Evaluation

An Improved Transient Electro-Thermal Model for Paralleled IGBT Modules

Optimization and Validation of Current Sharing in IGBT Modules With Multichips in Parallel

Experimental Investigations on Current Sharing Characteristics of Parallel Chips inside Press-pack IGBT devices

A Method to Balance Dynamic Current of Paralleled SiC MOSFETs With Kelvin Connection Based on Response Surface Model and Nonlinear Optimization

Current Sharing Analysis and Evaluation of Parallel DC-Link Capacitors in Vehicle Motor Drive

Multichip Parallel Double-Sided Cooling Silicon Carbide Power Module With Low Parasitic Inductance and Balanced Dynamic Current

A Novel Approach to Model and Analyze Uneven Temperature Distribution Among Multichip High-Power Modules and Corresponding Method to Respecify Device SOA

Parallel technique for IGBT modules applied in high-power converter

Current sharing of IGBT modules in parallel with thermal imbalance

Comparative Evaluation and Analysis of Parallel Package Method Based on 1.2-kV Interleaved Planar SiC Power Modules

Research on Parallel Operation Characteristics and Current Sharing Method of High Power IGBT

Symmetric Circuit Layout with Decoupled Modular Switching Cells for Multiparalleled SiC Mosfets

Effect of Asymmetric Layout and Unequal Junction Temperature on Current Sharing of Paralleled SiC MOSFETs with Kelvin-Source Connection

Effect of Distributed Decoupling Capacitors in Multi-chip SiC Power Modules on Current Sharing Mechanism

Design and Current Balancing Optimization of A 1700V/1000A Multi-chip SiC Power Module

Breaking Current Balance Enhancement for Parallel IGBT Modules in DC Circuit Breaker

Interleaved Planar Packaging Method of Multichip SiC Power Module for Thermal and Electrical Performance Improvement

Current Discrepancy Mitigation of Input-Parallel Output-Parallel Dual-Active-Bridge Converters Using Coupled Inductors