Abstract:A simple spray approach to fabricate superhydrophobic coatings on tile and glass substrates is presented. Commercial available polyphenylene sulfide (PPS) and hydrophobic silica (H-SiO(2)) powder were suspended in ethanol and the mixed suspensions were spray on substrates. After dried at different temperatures, surface coatings with different hydrophobicity were obtained. By observing the surface morphologies with scanning electron microscope (SEM) and atomic force microscope (AFM), and measuring water contact angles with a contact angle system, factors affecting the morphology, roughness and contact angle of the surface coatings, such as thermal treatment temperature and the weight ratio of H-SiO(2) to PPS, were investigated in detail. With the increase of the thermal treatment temperature, both the surface roughness and the contact angle increased when the temperature was lower than 280 degrees C. As the weight ratio of H-SiO(2) to PPS rose from 1: 10 to 1:1, more H-SiO(2) powders accumulated on the surface, leading to a significant increase of hydrophobicity. The surface coating obtained at 280 degrees C with the weight ratio of H-SiO(2) to PPS 1:1 showed a water contact angle higher than 150 degrees and a sliding angle lower than 4, exhibiting fascinating superhydrophobic properties. The surface coating could remain superhydrophobicity upon a further increase in thermal treatment temperature or the amount of H-SiO(2) powder. Moreover, the surface coatings showed high contact angles, larger than 150, for all the solutions with pH ranging from 1 to 14. The abrasion resistant property of the as-prepared superhydrophobic surface coating was tested using a homemade setup. Being scraped by freely-falling sands, the superhydrophobic coating could keep its high hydrophobicity, while a commercial hydrophobic coating transformed from hydrophobicity to hydrophilicity. This result implied our superhydrophobic surface coating was very stable. Moreover, chalk powders on the superhydrophobic surface coatings could easily be washed off with water, indicating good self-cleaning properties. The presented approach is convenient and can be potentially applied in fabrication of superhydrophobic surfaces in large scale.

A Facile Surface Treatment to Improve the Abrasion Resistance of Photosensitive Film for Screen Printing

Effect Of Surface Modification Of Titanium Dioxide On The Uv-C Aging Behavior Of Silicone Rubber

Facile preparation of wear-resistant and anti-fingerprint hard coating with chemisorption of fluorosilane by simple wet coating

Effect of Electroless Nickel Plating on the Abrasion Resistance of Screen Printing Plate Film

Surface Hydrophobicity of Polyester Film Grafted with Silicon Copolymer

The Surface Modification of Medical Polyurethane to Improve the Hydrophilicity and Lubricity: the Effect of Pretreatment

Preparation of High Wear-Resisting Superamphiphobic Robust Film by Self-Assembled Monolayer Surface Reaction

Preparation of UV-Curable Low Surface Energy Polyurethane Acrylate/Fluorinated Siloxane Resin Hybrid Coating with Enhanced Surface and Abrasion Resistance Properties

PREPARATION OF TRANSPARENT ABRASION-RESISTANT ORGANIC-INORGANIC HYBRID FILM

Surface modification of lithium-ion sieves by silane coupling agent for improved adsorption performance

The Effect of Polybenzimidazole Coating on the Morphology and Abrasion of Silk Screen Stencil Film

Optimizing the fabrication of abrasion-resistant and transparent organosilicon coating

A Stable and Indurative Superhydrophobic Film with Excellent Anti-Bioadhesive Performance for 6061 Al Protection

An Extremely Simple and Effective Strategy to Tailor the Surface Performance of Inorganic Substrates by Two New Photochemical Reactions

Effect of Aminopropyltriethoxysilane on the Adhesion of Flexographic Water-Based Ink to Packaging Films

Facile Preparation Of A Mechanically Robust Superhydrophobic Acrylic Polyurethane Coating

Confined Photo-Catalytic Oxidation: a Fast Surface Hydrophilic Modification Method for Polymeric Materials

Surface Modification Methods to Improve UV Inkjet Printing Performance of Ceramic

Significantly improve the water and chemicals resistance of alginate-based nanocomposite films by a simple in-situ surface coating approach

Enhancement of the Surface and Mechanical Properties of Polyurethane Coating Through Changing the Additive Ratio of Silane (Adv. Mater. Interfaces 11/2024)

PREPARATION AND PROPERTIES OF SUPERHYDROPHOBIC POLYPHENYLENE SULFIDE COMPOSITE COATINGS