Abstract:The injection strategy is commonly manipulated to control the stratification level to simultaneously achieve a low pollutant emission and a high efficiency in internal combustion engines. This paper reports on a joint experimental and numerical study of the emission characteristics and engine performance in a heavy-duty directinjection compression ignition (DICI) engine operating in the HCCI and PPC regimes, with a primary reference fuel made up of iso-octane (81% by volume) and n-heptane (19%) as a model gasoline fuel. The injection timing was varied to achieve different levels of stratification of the charge in the cylinder while the intake air temperature was adjusted accordingly to keep the same combustion phasing at 3 degrees crank angle (CA) after top dead centre (ATDC). The main results of the present study are: (1) In gasoline DICI engines, the fuel is injected into the cylinder at an earlier SOI. The combustion process can be divided into different regimes, HCCI, PPC, and transition from HCCI to PPC, depending on SOI. Two distinctive classes of in-cylinder combustion temperature distributions could be found from the simulation results for the studied engine: one was for the SOI range from -100 to -48 degrees CA ATDC, which was the HCCI regime and/ or the transition from HCCI to PPC regime, where the mean effective in-cylinder temperature was lower than 1700 K. The second class was for the SOI range from -44 to -20 degrees CA ATDC, where the combustion temperature was higher than 1850 K. This corresponded to the PPC regime. (2) The NOx emission was not only affected by the mean temperature but also the distribution of temperature in the cylinder. (3) The main source of unburned hydrocarbon (UHC) emission in the HCCI and the transition regimes was the fuel trapped in the crevice region where the oxidation process could not function properly. (4) Carbon monoxide (CO) emissions showed a non-monotonic variation with the injection timing, with one peak forming in the bowl region and one forming in the squish region during the transition from HCCI to PPC. The main source of CO emission was in the low temperature and fuel-lean region in the cylinder. (5) In the present engine operation, the pressure rise rate (PRR) in the PPC regime was higher than that in the HCCI regime, which is contrary to most results reported in the literature. This is a combined effect of low equivalence ratio in the piston bowl and in the squish region, and the stratification of the ignition delay time in the mixture. (6) Highest thermodynamic efficiency was achieved in the PPC regime with SOI from -44 to -31 degrees CA ATDC. In the transition from HCCI to PPC regime, the thermodynamic efficiency reached its lowest due to the poor combustion efficiency.

Partially Premixed Combustion (PPC) Stratification Control to Achieve High Engine Efficiency

Partially Premixed Combustion Optimization Using Double Injection Strategy in Transient Operation

Partially Premixed Combustion Based on Different Injection Strategies in a Light-Duty Diesel Engine

Modeling and Control of Gasoline PPC Engine Approaching High Efficiency with Constraints

Simultaneous Control of Soot Emissions and Pressure Rise Rate in Gasoline PPC Engine.

Emission Characteristics and Engine Performance of Gasoline DICI Engine in the Transition from HCCI to PPC

A Comparative Study on the Performance of Partially Premixed Combustion (PPC), Reactivity-Controlled Compression Ignition (RCCI), and RCCI with Reverse Reactivity Stratification (R-RCCI) Fueled with Gasoline and Polyoxymethylene Dimethyl Ethers (Poden)

Combustion Characteristics of Gasoline DICI Engine in the Transition from HCCI to PPC: Experiment and Numerical Analysis

A numerical investigation of gasoline/diesel direct dual fuel stratification (DDFS) combustion at high loads

Fuel Octane Effects on Gasoline Multiple Premixed Compression Ignition (MPCI) Mode

Potential of the Reverse-Reactivity Controlled Compression Ignition (R-RCCI) Combustion for Maintaining Ultra-Low Emissions and Enhanced Thermal Efficiency

Control of low-temperature polyoxymethylene dimethyl ethers (PODE<sub>n</sub>)/ gasoline combustion considering fuel concentration, fuel reactivity, and intake temperature at low loads

Control of low-temperature polyoxymethylene dimethyl ethers (PODEn)/gasoline combustion considering fuel concentration, fuel reactivity, and intake temperature at low loads

Temporally and Spatially Distributed Combustion in Low-Octane Gasoline Multiple Premixed Compression Ignition Mode

Investigation into Light Duty Dieseline Fuelled Partially-Premixed Compression Ignition Engine

Comparative Study of Low Octane Gasoline Multiple Premixed Compression Ignition and Conventional Diesel Combustion

Numerical resolution of multiple premixed compression ignition (MPCI) mode and partially premixed compression ignition (PPCI) mode for low octane gasoline

On improving the controllability of low-temperature combustion by building two-stage sequential high-temperature reactions in an ethanol/diesel dual-fuel engine using multiple injections

Present and Future of Premixed Compression Ignition Engines

Investigation of Two-Stage Split-Injection Strategies for a Dieseline Fuelled PPCI Engine

A Methodology for Stratified-Charge Preparation Via Low-Reactivity Fuel Multi-Injection Strategy in Intelligent Charge Compression Ignition (ICCI) Mode