Abstract:The presence of a significant amount of discontinuous joints results in the inhomogeneous nature of the shale reservoirs. The geometrical parameters of these joints exert effects on the propagation of a hydraulic fracture network in the hydraulic fracturing process. Therefore, mechanisms of fluid injection-induced fracture initiation and propagation in jointed reservoirs should be well understood to unleash the full potential of hydraulic fracturing. In this paper, a coupled hydromechanical model based on the discrete element method is developed to explore the effect of the geometrical parameters of the joints on the breakdown pressure, the number and proportion of hydraulic fractures, and the hydraulic fracture network pattern generated in shale reservoirs. The microparameters of the matrix and joint used in the shale reservoir model are calibrated through the physical experiment. The hydraulic parameters used in the model are validated through comparing the breakdown pressure derived from numerical modeling against that calculated from the theoretical equation. Sensitivity analysis is performed on the geometrical parameters of the joints. Results demonstrate that the HFN pattern resulting from hydraulic fracturing can be roughly divided into four types, i.e., crossing mode, tip-to-tip mode, step path mode, and opening mode. As β (joint orientation with respect to horizontal principal stress in plane) increases from 0° to 15° or 30°, the hydraulic fracture network pattern changes from tip-to-tip mode to crossing mode, followed by a gradual decrease in the breakdown pressure and the number of cracks. In this case, the hydraulic fracture network pattern is controlled by both γ (joint step angle) and β. When β is 45° or 60°, the crossing mode gains dominance, and the breakdown pressure and the number of cracks reach the lowest level. In this case, the HFN pattern is essentially dependent on β and d (joint spacing). As β reaches 75° or 90°, the step path mode is ubiquitous in all shale reservoirs, and the breakdown pressure and the number of the cracks both increase. In this case, β has a direct effect on the HFN pattern. In shale reservoirs with the same β, either decrease in k (joint persistency) and e (joint aperture) or increase in d leads to the increase in the breakdown pressure and the number of cracks. It is also found that changes in d and e result in the variation in the proportion of different types of hydraulic fractures. The opening mode of the hydraulic fracture network pattern is observed when e increases to 1.2 × 10−2 m.

Effect of Joint Parameters on Fracturing Behavior of Shale in Notched Three-Point-bending Test Based on Discrete Element Model

Study on the Effects of Joints Orientation and Strength on Failure Behavior in Shale Specimen under Impact Loads

Experiment and Discrete Element Modelling on Strength, Deformation and Failure Behaviour of Shale under Brazilian Compression

Study on Parallel Bond and Smooth Joint Dual Model Parameter Calibration of Mechanical Properties of Shale Under Pressure

Discrete Element Analysis for Hydraulic Fracture Propagations in Laminated Reservoirs with Complex Initial Joint Properties

Effect of Joint Geometrical Parameters on Hydraulic Fracture Network Propagation in Naturally Jointed Shale Reservoirs

Dynamic impact experimental and global cohesive element method to shale fracture characterization

Study on Fracture Behavior of Bedded Shale in Three-Point-bending Test Based on Hybrid Phase-Field Modelling

Experimental and Numerical Simulation Study of the Dynamic Crack Propagation and Fracture Properties of Bedding Shale Using Notched Semi-Circular Bend

Mutual Interference of Layer Plane and Natural Fracture in the Failure Behavior of Shale and the Mechanism Investigation

Effects of Bedding Geometry and Cementation Strength on Shale Tensile Strength Based on Discrete Element Method

Effects of Strain Rate and Bedding on Shale Fracture Mechanisms

Role of bedding plane in the relationship between Mode-I fracture toughness and tensile strength of shale

Experimental and Numerical Investigation of the Effect of Bedding Layer Orientation on Fracture Toughness of Shale Rocks

Shale Brazilian Split Test and Numerical Simulation of the Discrete Element Method

Dynamic Brazilian Splitting Experiment of Bedding Shale Based on Continuum-Discrete Coupled Method

Experimental investigation on the anisotropy of mode-I fracture and tensile failure of layered shale

Brazilian Splitting Experiment and Finite Element Simulation Analysis of the Influence of Bedding Loading Angle on Shale Fracture Mode

Particle Flow Simulation of Brazilian Splitting Failure Characteristics of Layered Shale

Evaluating the Mechanical Properties of Anisotropic Shale Containing Bedding and Natural Fractures with Discrete Element Modeling

Behavior of transversely isotropic shale observed in triaxial tests and Brazilian disc tests