Abstract:The flow separation during the process of flows around elliptical cylinders causes unsteady vortex shedding in the wake, which leads to the vortex-induced vibration of structures that can pose serious challenges across different engineering disciplines. Therefore, investigation on the suppression of the flow separation and the vortex shedding of elliptical cylinders so as to improve their aerodynamic characteristics has been one of the most active topics in recent decades. In this study, to investigate the effects of the passive and combined aerodynamic control on the aerodynamic characteristics of an elliptical cylinder immersed in uniform flow, wind tunnel tests of two 2D smooth elliptical cylinder models whose major axes are parallel or perpendicular to the incoming wind direction (i.e. the models S-parallel to and S-perpendicular to), two corresponding rough models with different surface roughness (i.e. the models R-parallel to and R perpendicular to with the relative roughness S-r of 5.3 x 10(-4) and 1.15 x 10(-3)) and four corresponding combined aerodynamic controlled models consists of the surface roughness and air suction (i.e. the models RS1 similar to RS4) have been carried out. The Reynolds numbers for the test models are about 5.52 x 10(4)-8.625 x 10(4). The surface roughness, suction flux coefficient C-Q, azimuthal locations of suction holes and placement of the major axes of the elliptical cylinders are considered as the main experimental variables, and the aerodynamic characteristics in terms of both the wind pressure coefficient distributions and the aerodynamic force coefficients of the smooth models, rough models and combined aerodynamic controlled models are compared to analyze the effect of the passive and combined aerodynamic control. The results show that the aerodynamic characteristics improvements generated by the mere surface roughness are limited but accompanying with some negative effects, especially for the models with their major axes being parallel to the incoming wind direction. As the air suction combined with the surface roughness is implemented, it is found that considerable and steady control effects on the aerodynamic characteristics can be generated as C-Q reaches 0.02. And the changes of the aerodynamic characteristics are gradually insignificant as C-Q is further increased for most cases. Among all the cases with different combinations of aerodynamic measures, quite effective aerodynamic characteristics improvements are acquired for the combined aerodynamic controlled model RS2 (its suction holes are located at the radial angles of 130 degrees and 230 degrees, and its major axis is parallel to the incoming wind direction) with S-r = 1.15 x 10(-3) and the model RS4 (its suction holes are located at the radial angles of 90 degrees and 270 degrees, and its major axis is perpendicular to the incoming wind direction) with S-r = 5.3 x 10(-4). The conspicuous reductions of the mean drag coefficient C-D for the two models mentioned above under C-Q = 0.02 are 87% and 59% respectively. Even so, the drag force coefficients of the model RS4 are much larger than those of the model RS2. The objective of the present study is to better understand the aerodynamic control effects and inherent control mechanism due to the changes of surface roughness and air suction, and to explore a proper combination mode of the passive and active aerodynamic control measures to achieve more aerodynamic characteristics improvement for elliptical cylinders.

Self-Suction and Self-Jet Control on Wind Loads and Turbulent Flow Structures over a Circular Cylinder

Passive jet control of flow around a circular cylinder

Passive Jet Approach to Control the Flow over a Circular Cylinder

Suppression of Unsteady Vortex Shedding from a Circular Cylinder by Using a Passive Jet Flow Control Method

Control of Vortex Shedding from Two Side-by-side Cylinders Using a Pair of Tangential Jets

Numerical Investigation of Steady Suction Control of Flow Around a Circular Cylinder

Large Eddy Simulation of Passive Jet Flow Control on the Wake of Flow Around a Circular Cylinder

Numerical study on passive-jet flow control for chamfered square cylinder

Numerical Simulation Study on a Passive Jet Flow Control Method to Suppress Unsteady Vortex Shedding from a Circular Cylinder

Active Wake Control of Flow Past a Circular Cylinder with Slot Jet

Controlled Flow Around a Finite Square Cylinder Through Suction at the Side and Free-End Leading Edge

Effects of Passive and Combined Aerodynamic Control on the Aerodynamic Characteristics of an Elliptical Cylinder

Sweeping jet control of flow around a circular cylinder

Suppression of Vortex-Induced Vibration of a Circular Cylinder by a Passive-Jet Flow Control

Numerical Study on the Vortex Motion Patterns Around a Rotating Circular Cylinder and Their Critical Characters

Fluid Dynamics Behind a Circular Cylinder Embedded with an Active Flapping Jet Actuator

Dynamics of Two-Dimensional Flow Around a Circular Cylinder with Flexible Filaments Attached

Self-Suction-and-Jet Control in Flow Regime and Unsteady Force for a Single Box Girder

Effects of Distributed Suction Through the Porous Side-Walls of a Square Cylinder on Separation and Wake Flows

Control of circular cylinder flow via bilateral splitter plates

Suppression of Vortex Shedding from a Circular Cylinder by Using a Suction Flow Control Method