Abstract:The divertor of the China Fusion Engineering Test Reactor (CFETR) requires a more efficient heat dissipation structure due to the high demand of heat flux dissipation of up to 20 MW/m 2 . Microchannel cooling technology excels in thermal management because of large heat transfer area to volume ratio and capability to achieve uniform temperature distribution. However, the heat transfer and thermal fatigue characteristics of W/Cu flat type mock-up with microchannel cooling structures at a heat flux of 20 MW/m 2 remains elusive. In this work, we analyzed the thermohydraulic (numerically) and thermal fatigue (experimentally) characteristics of W/Cu flat-type microchannel mock-up. The numerical results show that the thermal loaded area (W) of the microchannel mock-up possesses excellent temperature uniformity and heat transfer performance (the W surface temperature is only ∼685 °C even at a low volumetric flow rate V̇ = 5 L/min). We also compared the heat dissipation efficiency with the hypervapotron cooling channels, and found that the maximum temperature of the W surface and channel wall of the microchannel mock-up are reduced by 18.9 % and 46.7 %, respectively. The thermal stress analysis indicates that the maximum equivalent stress is concentrated in the middle region of the W surface at 15 s, with a value of 357.8 MPa that is below the maximum allowable stress of W material (425 MPa at 650 °C). The as-manufactured W/Cu flat-type microchannel mock-up successfully withstood a thermal fatigue test consisting of 1000 cycles at 20 MW/m 2 steady state heat load at V̇ = 30 L/min and T in = 25 °C. The maximum temperature of W is only 616.2 °C during the test, and some microcracks are detected on the W surface after the test; these microcracks are perpendicular to the heat loading surface, which have negligible influence to the heat transfer of the entire mock-up. This study reveals that the W/Cu flat-type microchannel mock-up is promising in dissipating ultra-high heat flux (steady-state 20 MW/m 2 ) on the divertor target, which might provide valuable insights for the engineering design of the CFETR divertor.

Study on Creep Fatigue of Heat Sink in W/RAFM Divertor for CFETR

Study on creep-fatigue of heat sink in W/CuCrZr divertor target based on a new approach to creep life

Fatigue and Fracture Analysis on EAST Divertor Monoblock Heat Sink in H-mode Operation

Impact of Creep-Fatigue Interaction on Divertor Tungsten under High Heat Flux

Study on Creep Behavior and Fracture Life Prediction Method of P92 Steel Based on Finite Element Analysis

Study on Creep-Fatigue Life of ODS-Cu As Heat Sink in Divertor PFU

Thermohydraulic and thermal fatigue characteristics of W/Cu flat-type microchannel mock-up for CFETR divertor

Conceptual Design Study for CFETR Divertor Target Using CLAM Steel As Structural Material

Preliminary Thermo-hydraulic and Mechanical Analysis for CFETR Divertor

A Review On The Development Of The Heat Sink Of The Fusion Reactor Divertor

Study of W/Cu Flat-Type Mock-Ups with Novel Hypervapotron Cooling Structure for CFETR Divertor

Creep-fatigue Properties and Deformation Mechanism of 316L Steel Fabricated by Laser Powder Bed Fusion (PBF-LB/M)

Estimation of Peak Heat Flux Onto the Targets for CFETR with Extended Divertor Leg

Study on Creep-Fatigue Damage Evaluation for Advanced 9%-12% Chromium Steels under Stress Controlled Cycling

Thermal fatigue of HIPed W/Cr–bronze divertor small scale mock-ups

Reliability research of hypervapotron under electromagnetic load for CFETR divertor

Lifetime measurement of a particular deep crack failure on a flat-type divertor mockup under cyclic high heat flux loading conditions

Thermomechanical Measurements for a Flat-Type Divertor Mock-Up: A Benchmark for Simulation

A life prediction method and damage assessment for creep-fatigue combined with high-low cyclic loading

Engineering Design and Analysis of the CFETR Divertor Remote Maintenance System

Progress, Load Study, and Structural Analysis of the CFETR Divertor Dome