Abstract:Organometal trihalide perovskites are emerging as a new generation of photovoltaic materials. They are abundant in nature and have rapidly increasing power conversion efficiencies (PCE) of above 15% in common hybrid (mixed organic/inorganic) thin-film-based solar cells.1–3 Up to now, perovskite films have been formed by film deposition approaches such as spin-coating, sequential deposition of the inorganic and organic precursor, and co-evaporation of the precursors.1, 2 Low-temperature solution processes are among the simplest ways to fabricate planar low-cost photovoltaic devices. However, perovskite crystallizes very rapidly, so it is very challenging to form uniform, continuous, and leakage-free perovskite films by solution methods.2 We developed two simple and effective low-temperature solution processes to fabricate high-efficiency perovskite devices (see Figure 1). In the first approach, we studied the influence of the ratio of the precursors methylammonium iodide (CH3NH3I) and lead iodide (PbI2) in a premixed solution. 3 We found that using a non-stoichiometric precursor solution (i.e., not in a simple ratio) was critical to forming stoichiometric (i.e., in a simple ratio) perovskite films. The compositions of the spun perovskite films were very sensitive to the substrate surface, and could be very different from those of the precursor solutions. We varied the composition of the precursor solution, and found a PbI2/CH3NH3Xmolar ratio of 0.6–0.7 gave the best surfacemorphology and electronic properties, such as doping concentration. We used a planar heterojunction device structure of ITO/ PEDOT:PSS/(CH3NH3I)/PCBMor ICBA/C60/BCP/aluminum, where ITO is a substrate of indium tin oxide, PEDOT:PSS is an electron-donating transparent conductive polymer, PCBM and ICBA are fullerene-derived electron acceptors, C60 is buckminsterfullerene (a spherical fullerene molecule), and BCP is 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline, an electrontransporting but hole-blocking layer. Figure 1. Schematic of the prepation of perovskite films by (a) spin coating of pre-mixed precursor of lead iodide (PbI2) and methylammonium iodide (CH3NH3I) and (b) an interdiffusion approach. ITO: Indium tin oxide, a transparent conducting oxide. PEDOT:PSS: A transparent, conductive polymer. MAI: Methylammonium iodide. MAPbI3 Methylammonium lead iodide.

High Performance Low-Bandgap Perovskite Solar Cells Based on a High-Quality Mixed Sn–Pb Perovskite Film Prepared by Vacuum-Assisted Thermal Annealing

Pseudohalide-Induced Recrystallization Engineering for CH3NH3PbI3 Film and Its Application in Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells

Low-bandgap Mixed Tin–lead Iodide Perovskite with Large Grains for High Performance Solar Cells

Reproducible One-Step Fabrication of Compact MAPbl(3-x)Cl(x) Thin Films Derived from Mixed-Lead-Halide Precursors

Vacuum-Assisted Thermal Annealing of CH3NH3PbI3 for Highly Stable and Efficient Perovskite Solar Cells

Light radiation annealing enables unidirectional crystallization of vacuum-assisted Sn–Pb perovskites for efficient tandem solar cells

Homogeneous Grain Boundary Passivation in Wide‐Bandgap Perovskite Films Enables Fabrication of Monolithic Perovskite/Organic Tandem Solar Cells with over 21% Efficiency

All‐In‐One Additive Enabled Efficient and Stable Narrow‐Bandgap Perovskites for Monolithic All‐Perovskite Tandem Solar Cells

Suppressing Bulk and Interfacial Recombination Losses in Sn–Pb Perovskites for Efficient Printable Low‐Bandgap Photovoltaic Devices

Sn‐Pb Binary Perovskite Films with High Crystalline Quality for High Performance Solar Cells

Hysteresis-free, stable and efficient perovskite solar cells achieved by vacuum-treated thermal annealing of CH3NH3PbI3

Facile Face-Down Annealing Triggered Remarkable Texture Development in CH3NH3PbI3 Films for High-Performance Perovskite Solar Cells.

Suppressing halide phase segregation in wide-bandgap perovskite film by co-doping strategy for high-performance and stable perovskite solar cells

Preparing High-Efficiency Perovskite Solar Cells

Power Conversion Efficiency Enhancement of Low-Bandgap Mixed Pb–Sn Perovskite Solar Cells by Improved Interfacial Charge Transfer

An efficient planar-heterojunction solar cell based on wide-bandgap CH3NH3PbI2.1Br0.9 perovskite film for tandem cell application.

Low‐Dimensional 2‐thiopheneethylammonium Lead Halide Capping Layer Enables Efficient Single‐Junction Methylamine‐Free Wide‐Bandgap and Tandem Perovskite Solar Cells

Molecule Anchoring Strategy Promotes Vertically Homogeneous Crystallization and Aligned Interfaces for Efficient Pb–Sn Perovskite Solar Cells and Tandem Device

Thin Single Crystal Perovskite Solar Cells to Harvest Below-Bandgap Light Absorption

High‐Performance Tin–Lead Mixed‐Perovskite Solar Cells with Vertical Compositional Gradient

Low-bandgap mixed tin–lead iodide perovskite absorbers with long carrier lifetimes for all-perovskite tandem solar cells