Abstract:To meet the demands of both processing and serving, to the best of our knowledge, this is the first report exhibiting large range control of the yield ratio from 0.31 to 0.96 with decent elongations over 10% in the same alloy with low-cost thermal treatments. The yield ratio of the metastable Ti-30Zr-5Mo alloy was regulated via adjusting trigger stress of the stress-induced phase transformation and work-hardening ability through changing the α phase content. Materials with acicular α phase of different contents were successfully prepared via low-cost thermal treatment. The effects of the α phase content on the stress-induced α ' martensite phase transformation and work hardening behavior were then investigated. In the Ti-30Zr-5Mo alloy with dual phases, due to the crystal difference and element partitioning, the hardness of the α phase is higher than that of the β matrix, and the hardness difference between the phases increases with increasing α phase. In addition to Mo, Zr plays an important role in stabilizing the β phase in high-Zr-containing alloys. Deformation initiates in the β phase of both single-phase and duplex-phase alloys. The deformation mechanism of the β phase is dependent on both the β domain and β stability. Due to the low trigger stress and excellent work hardening ability, stress-induced α ' martensite phase transformation is helpful to lower the yield ratio. As the α phase content increases, the trigger stress increases, and when the α phase content increases to 40%, dislocation slip dominates rather than stress-induced α ' martensite phase transformation, and a high yield strength of 944 MPa is obtained. The α/β phase interfaces act as effective obstacles to hinder dislocation movement and provide working hardening, and the obstruction effect is more significant with an increase in the hardness difference between the α and β phases. The stress-induced α ' phase transformation and/or the deformation coordination between the α and β phases guarantee decent elongations of no less than 10% in the large control of the yield ratio from 0.31 to 0.96 with a yield strength from 254 to 1013 MPa. It paves the way to develop "Unititaniam" alloys for wide possible applications.

Fabrication and Characterization of a Novel Β Metastable Ti-Mo-Zr Alloy with Large Ductility and Improved Yield Strength

Effects of Zr Addition on the Deformation Behavior, Microstructure and Mechanical Properties of Dental Ti Alloys

Design and microstructure-mechanical properties of a novel metastable β titanium alloy with excellent strength-plasticity matching

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Enhanced yield strength by fine grain strengthening and TRIP/TWIP effect of metastable β-type Ti-4V-2Mo-2Fe alloy with high ductility

Enhanced Mechanical Properties of Ti-5Al-5Mo-5V-3Cr-1Zr by Bimodal Lamellar Precipitate Microstructures Via Two-Step Aging

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Electron Beam Welding and Post Heat Treatment of a New Near-Beta High-Strength Ti-4Al-5Mo-5V-5Cr-1Nb Alloy

A strategy to regulate the yield ratio of a metastable high Zr-containing β titanium alloy: Synergistic effects of the β domain, β stability and β/α interfaces by varying the α phase content

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Research on the microstructure and properties of metastable β type Ti-8V4Mo3Cr3Zr3Al alloy with high strength and toughness

Trifunctional nanoprecipitates ductilize and toughen a strong laminated metastable titanium alloy

Martensite colony engineering: A novel solution to realize the high ductility in full martensitic 3D-printed Ti alloys

Designing ultra-strong and ductile hierarchical titanium alloys via interstitial solute-mediated multi-morphologic α-nanoprecipitates

Combination of multiple strengthening mechanisms facilitates excellent strength-ductility balance in metastable β titanium alloy

Oxygen interstitials make metastable β titanium alloys strong and ductile

α" martensite engineering: A strategy to achieve high yield strength and low yield ratio synergy for dual-phase titanium alloy

Design of a V-Ti-Ni alloy with superelastic nano-precipitates

Microstructure, mechanical properties and biocompatibility of novel Ti-20Zr-xMo alloys

Recent Advances in the Design of Novel Β‐titanium Alloys Using Integrated Theory, Computer Simulation, and Advanced Characterization