Abstract:A new jet fuel surrogate was developed in this work by emulating real jet fuel properties including physical, gas phase chemical properties and threshold sooting index (TSI). An intelligent optimization methodology was proposed to calculate the species composition that inherently satisfies both the physical and chemical characteristics as well as sooting tendency. Eight properties were selected as the target properties for the jet fuel surrogate development, including liquid density, viscosity, surface tension, cetane number (CN), hydrogen carbon (H/C) ratio, molecular weight (MW), lower heating value (LHV) and TSI. As a result, the CN, H/C ratio, LHV, TSI and density of the new jet fuel surrogate are reproduced excellently with very little deviations within 3%. The averaged deviation of viscosity is −6.318% and the deviations of MW is 9.776%. As the highest deviation among all properties, the averaged deviation of surface tension is 11.76%. Based on the newly developed jet fuel surrogate, a skeletal jet fuel surrogate mechanism with 5 components including decalin, n-dodecane, iso-cetane, iso-octane and toluene was developed. The skeletal jet fuel surrogate mechanism was significantly compacted into 74 species and 189 reactions by describing the chemistries for the oxidation of large molecules C4–Cn and small H2/CO/C1 molecules respectively, which makes it practical to be used for 3-D engine combustion simulations. The validations of ignition delay times present reasonable agreement between experiment and predictions over a wide range of equivalence ratios (0.5–2.0) and pressures (8–30 atm), except for a shift of negative temperature coefficient (NTC) region towards higher temperatures at Φ = 1.5, 20 atm: in the simulation the NTC region is from 830 K to 950 K while in the experiment the NTC region is from 740 K to 890 K. The predicted species concentrations can reproduce the trend of the experimental data, especially for O2, CO and CO2. The simulated laminar flame speed at 400 K and 470 K are with absolute averaged deviations of 3.5% and 4.06% respectively. The constant volume spray and combustion validations are reasonably good. In the engine combustion validations, a multistep soot model was embedded into the new jet fuel surrogate mechanism. The predicted in-cylinder pressure can reproduce the experimental data, expect for small deviations after the peak pressure (the averaged deviation is around 6.2% after the peak pressure). The embedded soot model can well reproduce the trend of the experimental data. It can be concluded that this new jet fuel surrogate mechanism is compact and robust for the utilization in diesel engine combustion simulation.

Atomization Performance and TG Analysis of Fischer–Tropsch Fuel Compared with RP-3 Aviation Fuel

INVESTIGATION OF ATOMIZATION PERFORMANCE ON A CENTRIFUGAL FUEL SLINGER WITH A PHASE DOPPLER ANEMOMETER

Research on Fuel Spray Characteristics of Coal-Made Fisch-Tropsch Process Diesel/methanol

Experimental Investigation on the Performance of an Aviation Piston Engine Fueled with Bio-Jet Fuel Prepared via Thermochemical Conversion of Triglyceride

Comparison of Atomization Characteristics of Jet A-1 and Alternative Aviation Fuels Using High-Speed Imaging Technique

Applying Fischer Tropsch and Its Pentanol Blends into an Aviation Compression Ignition Engine for PM Emissions Control

Alternative Aviation Fuels Evaluated for Lean-Flame NOx and Blowout, and Rich-Flame Soot Threshold

Study on Physicochemical Properties of Biodiesel and Fischer–Tropsch Diesel Exhaust Particle

Development of a New Jet Fuel Surrogate and Its Associated Reaction Mechanism Coupled with a Multistep Soot Model for Diesel Engine Combustion

Single-Pulse Shock Tube Experimental and Kinetic Modeling Study on Pyrolysis of a Direct Coal Liquefaction-Derived Jet Fuel and Its Blends with the Traditional RP-3 Jet Fuel

Combustion and emission characteristics of a compression ignition engine burning a wide range of conventional hydrocarbon and alternative fuels

Characterizing Combustion Performance and PM Emissions of an Aviation Compression Ignition Engine by Fueling RP-3 Kerosene and RP-3/pentanol Blends

Experimental investigation on short-time and long-time tribological performance of Fischer-Tropsch fuel compared with fossil diesel

Experimental Study on Combustion Characteristics of a Fischer‐tropsch Diesel/methanol Reactivity Controlled Compression Ignition Mode Engine

Effects of Low Temperature on Near-Nozzle Breakup and Droplet Size Distribution in Airblast Kerosene Spray

Variation of Gas Phase Combustion Properties of Complex Fuels During Vaporization: Comparison for Distillation and Droplet Scenarios

Sensitivity Analysis of Fuel Types and Operational Parameters on the Particulate Matter Emissions from an Aviation Piston Engine Burning Heavy Fuels

Experimental study on sooting characteristics of a direct coal liquefaction derived jet fuel and its blend with RP-3 jet fuel

An experimental and modeling study of oxidation of real RP-3 aviation kerosene

Experimental study on spray characteristics of aviation kerosene RP-3 in a radial rotary atomizer

Ignition characteristics of an alternative kerosene from direct coal liquefaction and its blends with conventional RP-3 jet fuel