Abstract:In order to predict flow behavior and find the optimum hot working processing parameters for 5754 aluminum alloy, the experimental flow stress data obtained from the isothermal hot compression tests on a Gleeble-3500 thermo-simulation apparatus, with different strain rates (0.1⁻10 s⁻1) and temperatures (300⁻500 &deg;C), were used to construct the constitutive models of the strain-compensation Arrhenius (SA) and back propagation (BP) artificial neural network (ANN). In addition, an optimized BP⁻ANN model based on the genetic algorithm (GA) was established. Furthermore, the predictability of the three models was evaluated by the statistical indicators, including the correlation coefficient (R) and average absolute relative error (AARE). The results showed that the R of the SA model, BP⁻ANN model, and ANN⁻GA model were 0.9918, 0.9929, and 0.9999, respectively, while the AARE of these models was found to be 3.2499⁻5.6774%, 0.0567⁻5.4436% and 0.0232⁻1.0485%, respectively. The prediction error of the SA model was high at 400 &deg;C. It was more accurate to use the BP⁻ANN model to determine the flow behavior compared to the SA model. However, the BP⁻ANN model had more instability at 300 &deg;C and a true strain in the range of 0.4⁻0.6. When compared with the SA model and BP⁻ANN model, the ANN⁻GA model had a more efficient and more accurate prediction ability during the whole deformation process. Furthermore, the dynamic softening characteristic was analyzed by the flow curves. All curves showed that 5754 aluminum alloy showed the typical rheological characteristics. The flow stress rose rapidly with increasing strain until it reached a peak. After this, the flow stress remained constant, which demonstrates a steady flow softening phenomenon. Besides, the flow stress and the required variables to reach the steady state deformation increased with increasing strain rate and decreasing temperature.

Flow Behavior of Al–6.2Zn–0.70Mg–0.30Mn–0.17Zr Alloy During Hot Compressive Deformation Based on Arrhenius and ANN Models

Microstructural Evolution and Constitutive Relationship of Al–Zn–Mg Alloy Containing Small Amount of Sc and Zr During Hot Deformation Based on Arrhenius-type and Artificial Neural Network Models

Dynamic Behavior and Modified Artificial Neural Network Model for Predicting Flow Stress During Hot Deformation of Alloy 925

Artificial neural network prediction to the hot compressive deformation behavior of Al–Cu–Mg–Ag heat-resistant aluminum alloy

Prediction of Flow Stress of Annealed 7075 Al Alloy in Hot Deformation Using Strain-Compensated Arrhenius and Neural Network Models

Prediction Flow Behaviour of a Magnesium Alloy in Hot Deformation and a Comparative Study by Using Hyperbolic Sine Model and ANN Model

Hot Deformation Flow Behaviour Modelling of Cast-Extruded Al 7075 Alloy Using Arrhenius Equations and Artificial Neural Network

Flow Stress and Microstructure Evolution of Al-6.2Zn-2.3Mg-2.3Cu Alloy During Hot Compression Deformation

Modeling of Flow Stress of As-Rolled 7075 Aluminum Alloy during Hot Deformation by Artificial Neural Network and Application

Modeling the Constitutive Relationship of Al–0.62Mg–0.73Si Alloy Based on Artificial Neural Network

A Characterization of Hot Flow Behaviors Involving Different Softening Mechanisms by Ann for As-Forged Ti-10v-2fe-3al Alloy

Flow Stress Behavior and Constitutive Modeling of 20mnnimo Low Carbon Alloy

Modeling the Hot Deformation Behaviors of As-Extruded 7075 Aluminum Alloy by an Artificial Neural Network with Back-Propagation Algorithm

Prediction of flow stress in a wide temperature range involving phase transformation for as-cast Ti-6Al-2Zr-1Mo-1V alloy by artificial neural network

The flow behavior of homogenizated Al-Mg-Si-La aluminum alloy during hot deformation

An Artificial Neural Network Model for Flow Stress of 2519 Aluminum Alloy at Elevated Temperature

Artificial Neural Network for Predicting the Flow Behaviors of Hot Compressed 2124-T851 Aluminum Alloy

A Modified Back Propagation Artificial Neural Network Model Based on Genetic Algorithm to Predict the Flow Behavior of 5754 Aluminum Alloy

A comparative study on improved Arrhenius-type and artificial neural network models to predict high-temperature flow behaviors in 20MnNiMo alloy.

Artificial Neural Network Modeling to Evaluate and Predict the Deformation Behavior of Zk60 Magnesium Alloy During Hot Compression

Modeling of hot deformation behavior and prediction of flow stress in a magnesium alloy using constitutive equation and artificial neural network (ANN) model