Abstract:Metal supported solid oxide fuel cells (MS-SOFC) possess several advantages like good mechanical property, easy assembling, fast start-up and capability to maintain redox stable due to fuel leakage. However, it has been a critical challenge to deposit cathode on the metal supported cell in the oxidizing atmosphere, which is mainly limited by the low calcination temperature yielding vulnerable electrolyte-electrode interface. The cathodes prepared in the protecting atmosphere are also not satisfied, instead it will increase the complexity of the cell fabrication process. Lower down the cathode deposition temperature using aqueous infiltration has become one of the optimized methods for MS-SOFC. Also, we have proposed an alternative way for the fabrication of metal supported single cell with robust cathode through whole cell reduction. Here, we present results of both above two approaches for the fabrication of nano-structured cathodes in MS-SOFC. The cells in this study are based on Fe-Ni (1:1 in mol ratio) support, Fe-Ni/YSZ anode and YSZ electrolyte prepared through tape-casting, thermal isostatic pressing and co-firing. As illustrated in the following schematic configuration, La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF) cathodes were deposited in the porous YSZ layer of the pre-reduced Ni-Fe|Ni-Fe-YSZ||YSZ||P-YSZ substrate by infiltration and fired at the cell operation temperature around 700 oC. A-site deficiency of ~4-8% was introduced into LSCF cathode and was expected to enhance the sintering activity of LSCF nano particles at low calcination temperature and to enhance the cathode performance by the excess cobalt and iron oxide at LSCF surface. As in the second approach, Sr0.95Ti0.3Fe0.63Ni0.07O3-δ – Gd0.1Ce0.9O1.95 (STFNi-GDC) graded cathode will be screen printed on the NiO-Fe2O3|NiO-Fe2O3-YSZ||YSZ|GDC substrate and fired at high temperature in air as normal cathode preparation procedure. Then the whole cell will be reduced in H2-Ar to obtain Fe-Ni alloy support and reduced STFNi cathode with in-situ exsolved (Fe,Ni) alloy nano particles anchored in the oxide surface. During the cell test, the reduced STFNi-(Fe,Ni) will be re-oxidized in air, forming the surface decorated iron and cobalt oxide particles, which were presumably to be expected to increase the cathode performance through improvement of oxygen surface exchange coefficient. Figure 1

Exsolved Fe–Ni nano-particles from Sr2Fe1.3Ni0.2Mo0.5O6 perovskite oxide as a cathode for solid oxide steam electrolysis cells

Exsolved Fe–Ni nano-particles from Sr<sub>2</sub>Fe<sub>1.3</sub>Ni<sub>0.2</sub>Mo<sub>0.5</sub>O<sub>6</sub> perovskite oxide as a cathode for solid oxide steam electrolysis cells

In-situ Exsolution of Nanoparticles from Ni Substituted Sr2Fe1.5Mo0.5O6 Perovskite Oxides with Different Ni Doping Contents

La0.6Sr0.4Fe0.8Ni0.2O3-δ perovskite with in-situ exsolved Ni-Fe nanoparticles as high activity catalyst for symmetric solid oxide electrolysis cells

In situ exsolved FeNi3 nanoparticles on nickel doped Sr2Fe1.5Mo0.5O6−δ perovskite for efficient electrochemical CO2 reduction reaction

Perovskite Oxyfluoride Ceramic with in Situ Exsolved Ni-Fe Nanoparticles for Direct CO2 Electrolysis in Solid Oxide Electrolysis Cells.

High-Performance Anode Material Sr2FeMo0.65Ni0.35O6−δ with In Situ Exsolved Nanoparticle Catalyst

Sr2FeNbO6 Applied in Solid Oxide Electrolysis Cell As the Hydrogen Electrode: Kinetic Studies by Comparison with Ni-YSZ

In Situ Exsolution of Core‐Shell Structured NiFe/FeOx Nanoparticles on Pr0.4Sr1.6(NiFe)1.5Mo0.5O6‐δ for CO2 Electrolysis

In-situ passivation of Fe nanoparticles exsolved from perovskite cathodes through Zinc doping for CO2 electrolysis

In-situ exsolved Ni-Cu alloy nanoparticles for optimization of perovskite electrodes in solid oxide electrolysis cell

In-situ exsolved FeNi nanoparticles on perovskite matrix anode for co-production of ethylene and power from ethane in proton conducting fuel cells

Iron-triggered Exsolution of FeNi Alloy Nanoparticles Via Topotactic Cation Exchange on Pr0.7Sr0.3Cr0.9Ni0.1O3−δ Perovskite for CO2 Electrolysis

In Situ Growth of LaSr(Fe,Mo)O4 Ceramic Anodes with Exsolved Fe–Ni Nanoparticles for SOFCs: Electrochemical Performance and Stability in H2, CO, and Syngas

In-Situ Formation of Nano-Structured Cathode on Metal Supported SOFC

Enhancing Electrode Performance by Exsolved Nanoparticles: A Superior Cobalt-Free Perovskite Electrocatalyst for Solid Oxide Fuel Cells.

Surface regulating of copper-iron nanoparticles bimetallic exsolution for enhanced performance and durability of double perovskite anode in solid oxide fuel cells

In Situ Construction of Metal/Perovskite Interfaces with Exsolved FeNi Alloy Nanoparticles for High-Temperature CO2 Electrolysis

High-Performance Sr0.95Fe0.8Mo0.1Ni0.1O3−δ Electrode for Reversible Symmetrical Solid Oxide Cells

Tuning Exsolution of Nanoparticles in Defect Engineered Ruddlesden–Popper Oxides for Efficient CO2 Electrolysis

Perovskite Chromite With In-Situ Assembled Ni-Co Nano-Alloys: A Potential Bifunctional Electrode Catalyst for Solid Oxide Cells