Abstract:In order to improve the ablation and oxidation resistance of C/C–ZrC–SiC composites in wide temperature domain, "Z-pins like" Zr–Si–B–C multiphase ceramic rods are prepared in the matrix. The influence of different sintering temperatures on the microstructure of ceramic rods and the ablative behavior of heterogeneous composites are studied. The results showed that the ZrB2 and SiC phases are formed in the sintered matrix, and the increase of sintering temperature is beneficial to improve the density of the ceramic rods. The ablation properties of samples have been greatly improved. The mass and linear ablation rate are 0.8 mg/s and 3.85 μm/s, respectively, at an ablation temperature of 3000 °C and an ablation time of 60 s. After ablation, the matrix surface is covered with SiO2 and ZrO2 mixed oxide films. This is due to the preferential oxidation of "Z-pins like" Zr–Si–B–C multiphase ceramic rods in the ablation process, and B2O3 melt, SiO2 melt, borosilicate glass, ZrSiO4 melt and ZrO2 oxide film can be generated successively from the low-temperature segment to the ultra-high temperature segment. These oxidation products can be used as compensation oxide melts for the healing of cracks and holes on the matrix surface in different temperature ranges and effectively prevent the external heat from spreading into the matrix. Therefore, C/C–ZrC–SiC composites with "Z-pins like" Zr–Si–B–C multiphase ceramic rods achieve ablation resistance in wide temperature domain.

Densification and Ablation Behavior of ZrB2 Ceramic with SiC And/or Fe Additives Fabricated at 1600 and 1800 °C

Ablation behavior and mechanisms of 3D Cf/ZrB2-SiC composite applied in long-term temperature up to 2400 °C

Preparation and flame ablation/oxidation behavior of ZrB2/SiC ultra-high temperature ceramic composites

Ablation behavior and mechanisms of 3D C<sub>f</sub>/ZrB<sub>2</sub>-SiC composite applied in long-term temperature up to 2400 C

Microstructural Evolution and Performance of Carbon Fiber-Toughened ZrB2 Ceramics with SiC or ZrSi2 Additive

Ablation behaviour of ultra-high temperature ceramic matrix composites: Role of MeSi2 addition

Pressureless Sintering of ZrC-based Ceramics by Enhancing Powder Sinterability

Densification, microstructure and mechanical properties of ZrB2–SiCw ceramic composites

Long-term ablation behavior and mechanisms of 2D-Cf/ZrB2-SiC composites at temperatures up to 2400 °C

Preparation and Characterization of ZrB 2 -Sic Ultra-High Temperature Ceramics by Microwave Sintering

Long-term Ablation Behavior of Al4SiC4-YB4 SiC4-YB4 Modified Cf/ZrB2-SiC F /Zrb2-Sic Composites at 2600 °C

Effects of SiC Platelet and ZrSi2 Additive on Sintering and Mechanical Properties of ZrB2-based Ceramics by Hot-Pressing

Structural characteristics and ablative behavior of C/C–ZrC–SiC composites reinforced with “Z-pins like” Zr–Si–B–C multiphase ceramic rods

Cyclic Ablation Behaviors of ZrB2–SiC Composites Sintered with Nano‐Sized Particles

Processing and Mechanical Properties of Zirconium Diboride‐Based Ceramics Prepared by Spark Plasma Sintering

Influence of Hot Pressing Temperature and SiC Content on the Microstructure and Mechanical Properties of ZrB2-SiC

Effect of temperature-dependent nano SiC on the ablation resistance of ZrC coating

Ablation Behavior of ZrB2–SiC–ZrO2 Ceramic Composites by Means of the Oxyacetylene Torch

Pressureless Sintering of Silicon Carbide Ceramics Containing Zirconium Diboride

Enhanced Mechanical Properties, Thermal Shock Resistance and Ablation Resistance of Si2BC3N Ceramics with Nano ZrB2 Addition

Preparation and Mechanical Properties of ZrB2-based Ceramics Using MoSi2 As Sintering Aids