Design of Equalizer Based on IP in HDTV Receiver ASIC

赵亮,徐元欣,袁锦辉,张明

DOI: https://doi.org/10.3969/j.issn.1003-353x.2003.02.007

2003-01-01

Abstract:A new method of implementing equalizer in HDTV which can sharply shorten designperiod and decrease design scale is proposed in this paper. This method is enlightened by IPtechnology applied in SoC. And this method is realized in our completed chip.

What problem does this paper attempt to address?

Research and Realization of HDTV Audio Decode Algorithm

张季,徐元欣,方健,张瑾,王匡

DOI: https://doi.org/10.3969/j.issn.1002-8692.2004.08.025

2004-01-01

Abstract:To reduce the computational amount and memory size of the HDTV(for DVB) audio decoder, the algorithm of sub-band synthesis filter has been optimized in this paper. Based on C-language simulation of the optimized decoder, fixed-point code has been converted from the floating-point code. This decoder can be realized in real-time on a fixed-point DSP, and it has a wide range of applications in HDTV source decoding and etc.
Design of a HDTV Audio Decoder on a Fixed Point DSP Chip

ZHANG Jin,XU Yuan-xin,ZHANG Ji,WANG Kuang

DOI: https://doi.org/10.3969/j.issn.1671-7147.2005.03.003

2005-01-01

Abstract:The paper describes a DVB based HDTV audio decoder used in multi-channel extension and presents an improved algorithm for the synthesis filter bank. It is found that when the symmetry of coefficient and the similarity of the allocation tables, computational amount and memory size are reduced by more than 50%. DSP/BIOS operating system simplifies developing various DSP systems. This decoder can also be used in Digital Audio Broadcasting systems.
A new VLSI design for Viterbi decoder based on ASIP

Zhiqiang Yi,Yuanxin Xu,Yun Li,Kuang Wang

DOI: https://doi.org/10.1109/ICCCAS.2002.1179065

2002-01-01

Abstract:Trellis Code Modulation (TCM) has been widely used because it can obtain 2.55∼7.37 dB coding gain without bandwidth expansion or reduction of the effective information rates. Since Viterbi decoder plays an important role in the realization of HDTV system, we conduct the research and development on integration of Viterbi decoder. This paper proposes a new VLSI design of Viterbi decoder using ASIPs based on hardware/software co-design idea. It reduces the total design time and enhances the reliability of VLSI. We have successfully used this method for the design of Viterbi decoder in the ASTC-HDTV receiver chip.
Equalizer in high definition television(HDTV) transmission system

归琳,仇佩亮,邹志永,王匡,董斌

DOI: https://doi.org/10.3785/j.issn.1008-973X.2002.03.016

2002-01-01

Abstract:A new type equalizer for HDTV transmission system based on VSB technology to cope with severely distorted channel situation is proposed. The ordinary equalizer, decision feedback (DFE) structure and recursive equalizing algorithm is used. Because of the multipath spreading in FIR, the ordinary DFE has a slow convergence of the weight coefficient in the former condition, and the recursive algorithm cannot work with the signal submerged in interference. The new equalizer adopts indirect equalizing style and new algorithm is used for fast estimation of the channel impulse responses used as initial weight coefficients of the adaptive equalizer. A modified DFE structure of decision feedback equalizer is proposed to get faster convergence of weight coefficients. The simulation results show that the new style equalizer can work well in severely distorted propagation channel while the ordinary equalizer cannot, and it was tested in Brazil.
Theory and Implementation of Tap-Mobile Equalizer

董斌,王匡,归琳,吴禀圣,邹志永,仇佩亮

DOI: https://doi.org/10.3321/j.issn:0372-2112.2002.08.027

2002-01-01

Tien Tzu Hsueh Pao/Acta Electronica Sinica

Abstract:A new equalizer called tap-mobile equalizer is presented. With the efficient algorithm of channel estimation, time delay and amplitude of all multipath are known so that the new equalizer just maintains those working taps. As the result shows, it consumes much less resource and improves greatly performance compared with conventional equalizer.
A Compact Passive Equalizer Design for Differential Channels in TSV-Based 3-D ICs

Kai Fu,Wen-Sheng Zhao,Da-Wei Wang,Gaofeng Wang,Madhavan Swaminathan,Wen-Yan Yin

DOI: https://doi.org/10.1109/access.2018.2884036

IF: 3.9

2018-01-01

IEEE Access

Abstract:In this paper, a compact passive equalizer for differential transmission channel is designed in TSV-based three-dimensional integrated circuits (3-D ICs). The compact size of the equalizer is achieved by a square shunt metal line. Three simplified odd-mode half circuit models are proposed for ground-signal-signal-ground (G-S-S-G) type TSVs, differential on-interposer interconnects, and differential channels, respectively. Those simplified models merely consist of frequency-independent elements and can accurately predict the differential insertion losses up to 20 GHz. Moreover, the electrical parameters of the proposed serial resistance-inductance (RL) type equalizers are derived from the system transfer functions and optimized by virtue of the time-domain inter-symbol interference cancellation technique. Further, the geometrical parameters of the RL equalizers are calculated by using a genetic algorithm based multi-objective optimization method. Finally, the performance of the designed RL equalizer is validated by both frequency- and time-domain simulations for 20 Gb/s high-speed differential signaling.
Theory and Implementation of Pre-Filtered Equalizer

董斌,王匡,仇佩亮,归琳

DOI: https://doi.org/10.3321/j.issn:1000-436x.2003.11.019

2003-01-01

Abstract:A new equalizer called pre-filtered equalizer is presented. It comprises a pre-filter and an adaptive equalizer. With the efficient algorithm of correlation estimation, time delay and amplitude of all multipath have been known. Then the parameters of the pre-filter are calculated with the help of the algorithm of multipath separation. The aberrance is reduced after the received signal pass through the pre-filter. At last, the remainder of ISI(intersymbol interference) is compensated by the adaptive equalizer. As the result shows, pre-filtered equalizer has greatly improved performance compared with conventional equalizer, and it can compensate the subpath whose amplitude is equal to that of the mainpath.
A New VLSI Design for Decoding of Reed-Solomon Codes Based on ASIP [HDTV]

YX Xu,F Xia,QD Yao,PL Qui,K Wang

DOI: https://doi.org/10.1109/icasic.2001.982597

2001-01-01

Abstract:Reed Solomon (RS) codes providing an efficient capability for correcting burst errors have been widely used. Some work has already been done in developing VLSI decoders for RS codes. This paper proposes a new VLSI design of RS decoder using ASIP based on software ideas. It shortens the design time and enhances the reliability of VLSI. We have successfully used the method for the design of RS decoder (207, 187) in the ATSC-HDTV receiver chip
Implementation of blind equalization algorithm for HF QAM based on DSP

Ang Li,Tiandong Duan,Xiangqian Fang,Wei Ren

DOI: https://doi.org/10.1109/WiCOM.2006.163

2007-01-01

Abstract:In this paper, a modified CMA-DDLMS equalization algorithm based on the automatic switch according to SNR is proposed This modified algorithm overcome the shortcoming of large residual error and preserves the fast convergence performance. The simulation results confirm the effectiveness of the proposed algorithm on HF QAM signal. The paper also gives the implementation procedure of the algorithm on TMS320C6711. © 2006 IEEE.
An Efficient Hardware Design for HDTV H.264/AVC Encoder

Liang Wei,Dan-dan Ding,Juan Du,Bin-bin Yu,Lu Yu

DOI: https://doi.org/10.1631/jzus.c1000201

2011-01-01

Abstract:This paper presents a hardware efficient high definition television (HDTV) encoder for H.264/AVC. We use a two-level mode decision (MD) mechanism to reduce the complexity and maintain the performance, and design a sharable architecture for normal mode fractional motion estimation (NFME), special mode fractional motion estimation (SFME), and luma motion compensation (LMC), to decrease the hardware cost. Based on these technologies, we adopt a four-stage macro-block pipeline scheme using an efficient memory management strategy for the system, which greatly reduces on-chip memory and bandwidth requirements. The proposed encoder uses about 1126k gates with an average Bjontegaard-Delta peak signal-to-noise ratio (BD-PSNR) decrease of 0.5 dB, compared with JM15.0. It can fully satisfy the real-time video encoding for 1080p@30 frames/s of H.264/AVC high profile.
Design and ASIC Realization of High Speed Equalization Combining Carrier Recovery

栾志斌,裴玉奎,葛宁

DOI: https://doi.org/10.16511/j.cnki.qhdxxb.2012.12.014

2012-01-01

Abstract:Single carrier ultra-wideband equalization seeks to provide up to 600 Mb/s throughput,high performance,low complexity and low power consumption.However,traditional equalization can not meet all of these requirements.This paper describes a method to overcome the shortcomings of traditional equalization with a loop structure for joint carrier recovery and parallel equalization.Simulations show that the loop structure simultaneously eliminates the inter-symbol interference and carrier frequency shift to meet the desired system performance requirements.The single carrier ultra-wideband receiver was produced in a TSMC 0.13 um CMOS process.Chip tests show that the loop structure consumes 12.4 mW,only 4% of the whole chip power consumption,with an area of 1.8 mm×0.9 mm,10% of the whole chip area;thus,this provides low power consumption with complexity.
ASIC Design Optimization of a Decision Feedback Equalizer at Single-Carrier Ultra-Wide Band

WEN Wujie,PEI Yukui,GE Ning

DOI: https://doi.org/10.16511/j.cnki.qhdxxb.2010.04.006

2010-01-01

Abstract:Chip design of single-carrier ultra-wide band equalization has to resolve problems resulting from the high throughput rate,high performance and low complexity. A structure suitable for ASIC implementation for a decision feedback equalizer (DFE) was developed based on the transposed structure of circuit presentation,the delayed-sign-LMS algorithm and the register resample of ASIC design methodology. The structure,using the standard LMS-DFE,eliminates the effect of the iteration bound on the throughput rate,which exists in adaptive filters containing feedback loops,and solves the problem of delay and power consumption due to high input fan out in transposed items. Simulations show that the BER performance loss is less than 0.1 dB compared with the standard-LMS. The synthesized result in a 0.18 μm CMOS process shows that the area and power consumption items are improved by 23% and 33% compared with the transposed delayed-LMS item,with the speed reaching 125 Mb/s.
Design of Dual-mode Equalizer for QAM Demodulator in FPGA

Zhou Jiang,Zhi Liu,Ronghua Jin,Xiaoyang Zeng

DOI: https://doi.org/10.1109/ICSICT.2006.306246

2007-01-01

Abstract:This paper deals with the design of a dual-mode equalizer for QAM demodulator in FPGA. The fractionally spaced mode is supported as well as conventional symbol-spaced mode without changing the clock rate. The equalizer can also be configured to handle spectrum inversion. Meanwhile we optimize the implementation architecture to reduce hardware complexity. Test results show that the equalizer can achieve high reliability at low hardware costs
The Hardware/Software Co-design of Audio Decoding Used in HDTV

汪斌,姚庆栋,刘鹏,张明,韦晓东

2004-01-01

Abstract:Dolby AC3 standard is used as the audio decoding standard to research the hardware/software co-design method of HDTV audio decoding based on Virgo-IP-Core and a new method is present to realize the hardware/software partition by setting models for the key sub-functions of AC3 decoding program. That is, after decoding AC3 bit stream by software, the models are set up for the key sub-functions to get the extended instructions of RISC core. Through this extension, the speed of AC3 decoding is fastened, the memory space is reduced and the gates of the whole system are lessened. Next, the detail hardware of extended instruction is given. Finally, the performance of the whole system is analyzed by using the hardware/software co-evaluation method.
Design of Equalizer in 2.5 Gbps Transceiver System

覃正才,王涛,洪志良

DOI: https://doi.org/10.3969/j.issn.1000-3819.2002.03.003

2002-01-01

Abstract:An equalizer circuit in receiver for 2 5 Gbps transceiver has been designed by using technique of on chip programmable equalization. The standard process of 0.18 μm CMOS and 1.8 V power supply are used. Using UMC models, the circuits are simulated by Cadence SpectreS simulators. In the range of 0～125°C, at ff, tt or ss process corner, and in the power supply range of 1.8 V±10%, the simulation results show the circuits work well and robustly. In the typical case, the total power dissipation is 40 mW.
A Parallel Serial Filtering Mixed Advanced ID Interpolation Architecture for AVS

Kai Luo,Dongxiao Li,Yu Dai,Zheng Zhu,Ming Zhang

DOI: https://doi.org/10.1109/icasic.2007.4415742

2007-01-01

Abstract:This paper presents an advanced ID interpolation architecture for AVS video coding standard. Previous approaches have demerit of low data throughput. The proposed design parallel filters the horizontal data and serial filters the vertical data, thus greatly improve the throughput. Experimental result shows it outperforms conventional designs in processing cycle and chip area. The prototype design costs 26.2 K gates when synthesized at 108 MHz using 0.18 mum CMOS technology.
Parametric Design of RS Decoding Module in HDTV

张力,徐元欣,王匡,张明

DOI: https://doi.org/10.3969/j.issn.1002-8692.2004.03.017

2004-01-01

Abstract:In this paper, a generally applicable design of RS decoding module is put forward, synthesizing Reed-Solomon codes in different HDTV standards, and the design result is satisfactory.
Design of Graphic Equalizer Based on Inter-Band Interference

SANG Xiao-jun,CHEN Xiao-guang

DOI: https://doi.org/10.3969/j.issn.1672-2892.2011.01.013

2011-01-01

Abstract:Audio graphic equalizers are implemented by filter banks.State-of-the-art algorithms either suffer poor performance in frequency response,or work on high complexity.When two adjacent bands are expected to lift or attenuate by equal amount,huge ripples appear in frequency response.This paper analyzes inter-band interference model,and the relationship between peak gain with its spectral leakage in bell filter.Finally,an offline design method and a reference look-up table are presented to reduce the complexity and eliminate the spectral ripple.
Design and Implementation of Video Image-Scaling Module

汪颖,陈涛,王维东,张明

DOI: https://doi.org/10.3969/j.issn.1002-8692.2004.06.012

2004-01-01

Abstract:The paper introduces the image-scaling module for video processing chip. The module is designed for both integral and fractional scaling ratios and utilizes variable filter window for calculating pixels of a scaled image to realize pixel re-sampling. The algorithm is implemented, and can achieve fine image quality with lower hardware cost. The chip with image scaling function will be used in LCD TV or various other digital display devices.
Design of Digital Class-D Audio PWM Modulating Chip Based on Haft Band Filter

王升杨,李挥,邳雪松,马子龙

DOI: https://doi.org/10.3969/j.issn.1002-8684.2009.10.009

2009-01-01

Abstract:A digital class-D audio amplifier,PWM modulating chip,based on half band filters is designed.The FPGA verification and ASIC implementation are introduced.Compared with the ordinary method based on CIC filter,the proposed method can remarkably decrease the SNR loss of the data path without too much increasing of the die size.

Design of Equalizer Based on IP in HDTV Receiver ASIC

Research and Realization of HDTV Audio Decode Algorithm

Design of a HDTV Audio Decoder on a Fixed Point DSP Chip

A new VLSI design for Viterbi decoder based on ASIP

Equalizer in high definition television(HDTV) transmission system

Theory and Implementation of Tap-Mobile Equalizer

A Compact Passive Equalizer Design for Differential Channels in TSV-Based 3-D ICs

Theory and Implementation of Pre-Filtered Equalizer

A New VLSI Design for Decoding of Reed-Solomon Codes Based on ASIP [HDTV]

Implementation of blind equalization algorithm for HF QAM based on DSP

An Efficient Hardware Design for HDTV H.264/AVC Encoder

Design and ASIC Realization of High Speed Equalization Combining Carrier Recovery

ASIC Design Optimization of a Decision Feedback Equalizer at Single-Carrier Ultra-Wide Band

Design of Dual-mode Equalizer for QAM Demodulator in FPGA

The Hardware/Software Co-design of Audio Decoding Used in HDTV

Design of Equalizer in 2.5 Gbps Transceiver System

A Parallel Serial Filtering Mixed Advanced ID Interpolation Architecture for AVS

Parametric Design of RS Decoding Module in HDTV

Design of Graphic Equalizer Based on Inter-Band Interference

Design and Implementation of Video Image-Scaling Module

Design of Digital Class-D Audio PWM Modulating Chip Based on Haft Band Filter