Application of Cold Crucible Technique in the Nuclear Waste Treatment

HU Tanghua,FENG Xiaogui,BAO Weimin,SONG Chongli

DOI: https://doi.org/10.3321/j.issn:0253-3219.2001.06.017

2001-01-01

Abstract:The principal,development and application of the cold crucible technology in the treatment of radioactive wastes were reviewed.The importance of the cold crucible technique for solidification of radioactive waste was described.

What problem does this paper attempt to address?

Development and Advances in Cryogenic Treatment Technique and Device

XIA Yu-liang,JIN Tao,TANG Ke,XU Bin,ZHANG Xiao-zhong,CHEN You-jun

DOI: https://doi.org/10.3969/j.issn.1007-7804.2007.01.002

2007-01-01

Abstract:Cryogenic treatment attracts much attention and obtains practical application in wide fields,since it helps to improve the mechanical performance of some metal or nonmetal materials,such as strength,hardness,abradability and dimension stability.The selection of the treatment process and device is important for this technique.Based on a review of main influence factors during cryogenic treatment,some typical examples of treatment device are categorized and introduced.A short prospect is also present for future development of this technique.
Research and Development of Cold Crucible Melting and Casting Technology

CHEN Rui-run,GUO Jing-jie,DING Hong-sheng,SU Yan-qing,BI Wei-sheng,LIU Lin,JIA Jun,FU Heng-zhi

DOI: https://doi.org/10.3321/j.issn:1001-4977.2007.05.001

2007-01-01

Abstract:The principle,characteristic,researches,application and the development of the cold crucible is reviewed.Cold crucible has many advantages,such as melting high melting point metal,no pollution,uniform composition and so on.As a result cold crucible is extensive researched and applied in the following field.Cold crucible can be used for melting reactive metals without contamination,and create an alloy of uniform composition.Through ignition cold crucible can be applied for preparing ceramic materials.Cold crucible continuous casting can improve surface quality and optimize structure.Titanium alloys can be directional solidified by cold crucible.Massive photovoltaic multicrystalline silicon billet is continuous solidified from cold crucible,in the billet the impurity content is kept at the same low level as it is in the feed stock.Cold crucible spray and deposition can melt many kinds of alloys and have more application area.The characteristic and advantages of cold crucible decide that it will be received more attention and has more development area.
Solidification of radioactive wastes by cement-based materials

Junfeng Li,Lei Chen,Jianlong Wang

DOI: https://doi.org/10.1016/j.pnucene.2021.103957

IF: 2.461

2021-01-01

Progress in Nuclear Energy

Abstract:Solidification is the most widely applied treatment method for radioactive waste, and cement is the most commonly used material for the immobilization of radionuclides, due to its advantages, such as high mechanical strength of the solidified waste form, easy operation and low cost. In the past decades, great efforts have been made to improve the cementation technology for enhancing the performance of the solidified waste, including mechanical properties and durability, and for reducing the leaching of radionuclides. Particularly, special cements have been developed based on Portland cement for solidifying radioactive waste. In this review article, various types of cements were briefly introduced, including Portland cement, alkali-activated cement, geopolymer, calcium aluminate cement, and sulphoaluminate cement; the main parameters used to characterize the performance of the solidified waste forms were summarized, such as package capacity, compressive strength, tensile strength, and leaching resistance, and the measures taken to improve these performances were analyzed; the mechanisms for the immobilization of radionuclides in cements were discussed, mainly involving two ways: chemically fixing them in an insoluble form, and physically adsorbing and trapping them in a rigid, durable matrix. This review will deepen the understanding of the principle and application of the solidification of radioactive wastes by various cement-based materials.
Ceramics for high level radioactive waste solidification

Li Wang,Tongxiang Liang

DOI: https://doi.org/10.1007/s40145-012-0019-8

IF: 11.534

2012-01-01

Journal of Advanced Ceramics

Abstract:Several countries reprocess their nuclear spent fuel using the Purex process to recover U and Pu as MOX fuel. The high level radioactive waste (HLW) produced during this reprocessing is a complex mixture containing both radioactive (fission products, minor actinides) and non-radioactive elements. Since HLW shows high rate heat release and contains some long half-life and biologically toxic radionuclide, its treatment and disposal technology is complex, difficult and high cost. HLW treatment and disposal become a worldwide challenge and research focus. In order to minimize the potential long-term impact of HLW, studies on enhanced chemical separation processes of long-lived radionuclides are in progress. Two options are then envisaged for these separated radionuclides: (a) transmutation into short-lived or non-radioactive elements, (b) immobilization in highly durable ceramic matrix instead of borosilicate glass. In this paper, we briefly review the composition, structure, processing and product properties of some ceramic candidates for inert matrix fuels (IMF) and the immobilization of high level radioactive waste.
Radioactive Wastewater Treatment Technologies: A Review

Hailing Ma,Minghai Shen,Yao Tong,Xiao Wang

DOI: https://doi.org/10.3390/molecules28041935

IF: 4.6

2023-02-18

Molecules

Abstract:With the wide application of nuclear energy, the problem of radioactive pollution has attracted worldwide attention, and the research on the treatment of radioactive wastewater is imminent. How to treat radioactive wastewater deeply and efficiently has become the most critical issue in the development of nuclear energy technology. The radioactive wastewater produced after using nuclear technology has the characteristics of many kinds, high concentration, and large quantity. Therefore, it is of great significance to study the treatment technology of radioactive wastewater in reprocessing plants. The process flow and waste liquid types of the post−treatment plant are reviewed. The commonly used evaporation concentration, adsorption, precipitation, ion exchange, biotechnology, membrane separation, and photocatalysis are summarized. The basic principles and technological characteristics of them are introduced. The advantages and disadvantages of different single and combined processes are compared, and the development trend of future processing technology is prospected.

chemistry, multidisciplinary,biochemistry & molecular biology
Extraction of Actinides and Lanthanides by Supercritical Fluid

Zhu Liyang,Duan Wuhua,Xu Jingming,Zhu Yongjun

DOI: https://doi.org/10.1115/1.4002354

2010-01-01

Journal of Engineering for Gas Turbines and Power

Abstract:Reprocessing of used nuclear fuel and treatment of nuclear waste are important issues for the sustainable development of nuclear energy. It is necessary to develop novel nuclear waste treatment technologies to meet the goal of minimizing the secondary liquid waste. Supercritical fluids are considered green solvents in chemical engineering process. It gains growing interest to treat nuclear waste using supercritical fluid extraction recently, because it can greatly decrease the secondary liquid waste with high radioactivity. During the past two decades, extraction of actinides and lanthanides by supercritical fluid has been intensively studied in some countries, and many important progresses have been made. However, the prospect of industrial application of supercritical fluid extraction technology in reprocessing of used nuclear fuel and treatment of nuclear waste is still unclear. In this paper, extraction of actinides and lanthanides from various matrixes or from their oxides by supercritical fluid including the experimental results, extraction mechanism and kinetic process was reviewed. The engineering demonstration projects were introduced. The trend of industrial application of supercritical fluid extraction technology in nuclear waste management was also discussed.
Temperature Field during Melting and Solidification of Glass with Electromagnetic Cold Crucible

Yuzhou Ming,Zheng Li,Dewei Cao,Yaohua Yang,Rui Wang,Ruirun Chen,Jingjie Guo

DOI: https://doi.org/10.15980/j.tzzz.2017.11.010

2017-01-01

Abstract:Through using cold crucible to curing nuclear waste and deeply burying solidified body,the detriment of nuclear waste for environment could be prevented.The temperature distribution of melt interior will impact the quality of the solidified body directly.A temperature field calculation model was established by Ansys software.Then accuracy of the model was verified by experiments.The distribution of temperature field in melt was simulated and the distribution of temperature was analyzed at different power parameters by using the model.The results reveal that with the increase of current value and frequency,heating time to the operating temperature can be shortened,however,the temperature gradient can be enlarged,which cause the uneven distribution in melt.Smelting process should set mechanical agitation on the basis of physical conditions.
Research Progress in Cementation of Radioactive Wastes

SUN Qi-na,LI Jun-feng,WANG Jian-long

2010-01-01

Abstract:The advances in cement chemistry and the new cement products,the application of admixtures,additives and fibers can contribute to the formulation study of radioactive wastes cementation.The application status of cement matrices for immobilization of radioactive wastes,including Portland cement,alkali-activated slag cement,calcium sulfoaluminate cement etc.was reviewed.The admixtures,additives and fibers used for improving cemented wastes performance,including wastes loading,compressive strength and long-term durability of cemented wastes were introduced.The objective of this review is to provide some new thoughts for the research and development of radioactive wastes cementation.
Treatment of Cs-sorbed Zeolite As Spent Adsorbent by Cold Sintering for Stabilization and Solidification of Secondary Wastes

Ziying Cao,Chi Zhang,Pengju Chen,Shunyan Ning,Lifeng Chen,Yupeng Xie,Yan Wu,Hao Wu,Yuezhou Wei,Weiqun Shi,Xiangbiao Yin

DOI: https://doi.org/10.1016/j.cej.2024.156626

IF: 15.1

2024-01-01

Chemical Engineering Journal

Abstract:The effective and efficient solidification of Cs-sorbed zeolite (CSZ), a secondary solid radioactive waste produced in the Fukushima nuclear power plant-1 (NPP-1) accident, is highly urgent for nuclear post-accident remediation. In present study, cold sintering treatment was introduced as the novel technique and single step process to stable solidification of CSZ for its long-term disposal. The effects of transient liquid solutions, sintering temperature, uniaxial pressure, holding time, and particle size on densification of cold sintered zeolite (CS-Z) were systemically investigated. It was concluded that customized liquid agent (CLA) served as the transient liquid prior than other several acidic or basic solutions for zeolite densification, and the optimal condition of cold sintering was determined to be 200 degrees C, 500 MPa, 10 wt% CLA, 5 min, and particle size of 36-75 mu m, respectively. Such CS-CSZ ceramics achieved high and impressive compressive strength of 382.9 MPa, micro hardness of 1.8 GPa and 93.0 % of the theory relative density. The Cs leaching index and leaching rates of the CS-CSZ ceramic were measured to be similar to 7.0 and 10(-5)-10(-4) gcm(-2)d(-1) magnitude order at 25 degrees C. Further structural and spectral analysis suggested mechanisms of zeolite densification and Cs immobilization during cold sintering involves combined mechanical and chemical effects. All these results suggested that cold sintering might potentially be an effective, efficient, economical, and environment friendly technique for the stable solidification of CSZ, which are expected to inspire new insights to establish novel practical technologies for treatment and disposal of the nuclear post-accident secondary wastes.
Application of melting technology in the treatment of nonferrous hazardous waste residues

Ying Fu,Shaoping Kuang,Benqi Yuan,Lei Jing,Puliang Lu,Yufu Liu,Lianchao Han

DOI: https://doi.org/10.1080/00084433.2024.2415221

2024-10-20

Canadian Metallurgical Quarterly

Abstract:In order to find a more effective treatment method for non-ferrous hazardous waste residues, the research proposed the fusion disposal technology of collaborative resource residues. The empirical results showed that the leaching concentrations of Cr and Pb of the molten products of the resource residue were maintained at 0 mg/L, and the final leaching concentrations of most heavy metals were within 0.10 mg/L, which showed low toxicity to the environment. The above results show that the fusion disposal technology of collaborative resource residue is an effective treatment method. The fusion disposal technology not only reduces the heavy metal leaching concentration of non-ferrous metals, but also promotes the development of hazardous waste residue treatment technology. Dans le but de trouver une méthode plus efficace de traitement des résidus de déchets dangereux non ferreux, cette étude propose une technique d'élimination par fusion des résidus de co-ressources. Les résultats empiriques montrent que les concentrations de lixiviation du Cr et du Pb des produits de fusion des résidus de ressources restent à 0 mg/L et que la plupart des métaux lourds ont des concentrations finales de lixiviation inférieures à 0,10 mg/L, ce qui est peu toxique pour l'environnement. Les résultats ci-dessus montrent que la technique d'élimination par fusion des résidus coressorés est une méthode de traitement efficace. La technique d'élimination par fusion proposée par la recherche a non seulement permis de réduire les concentrations de lixiviation des métaux non ferreux par les métaux lourds, mais aussi de promouvoir le développement des techniques de traitement de leurs résidus dangereux.

metallurgy & metallurgical engineering
Methods of Thermal Treatment of Radioactive Waste

Leon Fuks,Irena Herdzik-Koniecko,Katarzyna Kiegiel,Agnieszka Miskiewicz,Grazyna Zakrzewska-Koltuniewicz

DOI: https://doi.org/10.3390/en15010375

IF: 3.2

2022-01-05

Energies

Abstract:Throughout the world, and especially in the European Union, numerous technologies for the thermal treatment of radioactive waste are available or being developed. These technologies can be applied to a large range of different radioactive waste streams, including non-standard types of waste that present specific waste management challenges. Thermal treatment can result in a significant reduction in volume and hazard, which are beneficial for safe storage and disposal. Thermal treatment also removes organic material that can form complexing agents and increase the mobility of radionuclides in the landfill. In the paper, basic thermal techniques are presented, and some examples of the installations are shown. Common knowledge of these methods may result in an increased public acceptance of nuclear energy in a country just introducing it, as Poland is.

energy & fuels
Progress in Treatment Processes of Radioactive Wastewater from Nuclear Accident

Cai Xuan,Liu Yan,Zhang Yun,Liu Xiang

DOI: https://doi.org/10.14159/j.cnki.0441-3776.2012.06.001

2012-01-01

Chemistry

Abstract:Nuclear accidents might do great harm to the safety and health of human beings and the environment.In order to control the spread of radioactive matter,we should place enough emphasis on effective treatment and disposal of radioactive wastewater.This article summarized the treatment experience of Chernobyl nuclear explosion and Fukushima nuclear leakage in Japan,listed some effective treatment processes recommended by USEPA and UKHPA,and reviewed the research progress of adsorption,ion exchange,membrane separation and combined processes,which might offer China some reference in the establishment and improvement of radioactive wastewater treatment and disposal after nuclear accident.
Applications of Crushing and Grinding-Based Treatments for Typical Metal-Containing Solid Wastes: Detoxification and Resource Recovery Potentials.

Hongping He,Bo Yang,Deli Wu,Xiaofeng Gao,Xunchang Fei

DOI: https://doi.org/10.1016/j.envpol.2022.120034

2022-01-01

Abstract:Metal-containing solid wastes can induce serious environmental pollution if managed improperly, but contain considerable resources. The detoxification and resource recoveries of these wastes are of both environmental and economic significances, being indispensable for circular economy. In the past decades, attempts have been made worldwide to treat these wastes. Crushing and grinding-based treatments have been increasingly applied, the operating apparatus and parameters of which depend on the waste type and treatment purpose. Based on the relevant studies, the applications of crushing and grinding on four major types of solid wastes, namely spent lithium-ion batteries (LIBs) cathode, waste printed circuit boards (WPCBs), incineration bottom ash (IBA), and incineration fly ash (IFA) are here systematically reviewed. These types of solid wastes are generated in increasing amounts, and have the potentials to release various organic and inorganic pollutants. Despite of the widely different texture, composition, and other physicochemical properties of the solid wastes, crushing and grinding have been demonstrated to be universally applicable. For each of the four wastes, the technical route that involving crushing and grinding is described with the advantages highlighted. The crushing and grinding serve either mainstream or auxiliary role in the processing of the solid wastes. This review summarizes and highlights the developments and future directions of crushing and grinding-based treatments.
Progress in Research on Cold Crucible Directional Solidification of Titanium Based Alloys

Chen Ruirun,Guo Jingjie,Chen Xiaoyu,Dong Shulin,Ding Hongsheng,Su Yanqing,Fu Hengzhi

2014-01-01

Abstract:Cold crucible directional solidification (CCDS) is a newly developed technique, which combines the advantages of the cold crucible and continuous melting. It can be applied to directionally solidify reactive, high purity and refractory materials. This paper describes the principle of CCDS and its characteristics; development of the measurement and numerical calculation of the magnetic field, flow field and temperature field in CCDS; and the CCDS of Ti based alloys. The paper also reviews original data obtained by some scholars, including the present authors, reported in separate publications in recent years. In Ti based alloys, Ti6Al4V, TiAl alloys and high Nb-containing TiAl alloys, have been directionally solidified in different cold crucibles. The crosssections of the cold crucibles include round, near rectangular and square with different sizes. Tensile testing results show that the elongation of directionally solidified Ti6Al4V can be improved to 12.7% from as cast 5.4%. The strength and the elongation of the directionally solidified Ti47Al2Cr2Nb and Ti44Al6Nb1.0Cr2.0V are 650 MPa/3% and 602.5 MPa/1.20%, respectively. The ingots after CCDS can be used to prepare turbine or engine blades, and are candidates to replace Ni super-alloy at temperatures of 700 to 900 °C.
Treatment Method of Radioactive Waste Liquid Containing U and Cs

Caixiong Yin,Chunhai Lu,Qigang Ye,Xiangqian Dong

DOI: https://doi.org/10.54097/ije.v3i3.014

2023-12-01

International Journal of Energy

Abstract:Radioactive waste liquid will not only cause heavy metal and radiation pollution in the environment, but also enter the human body from a variety of ways, threatening human life and health. Among them, uranium and cesium, due to their high fission yield, long half-life and high solubility of salt compounds in water, need to be treated urgently. The treatment methods of radioactive u and C waste liquid, such as ion exchange method, solvent extraction method, adsorption method, membrane separation method, chemical precipitation method, biological treatment method, adsorption method and combined process, are combed. The principle, characteristics and application of the method are reviewed, and the research direction and development trend are prospected. It has a certain reference value for the selection of radioactive waste treatment methods in different situations.
Treatment and disposal of spent radioactive ion-exchange resins produced in the nuclear industry

jianlong wang,zhong wan

DOI: https://doi.org/10.1016/j.pnucene.2014.08.003

IF: 2.461

2015-01-01

Progress in Nuclear Energy

Abstract:Ion exchange resins are employed extensively in the nuclear industry to remove the radioactive contaminants such as neutron activation products and fission products which may have leaked from fuel elements. The spent radioactive ion exchange resins have been produced during the operation of the nuclear facilities in the nuclear industry. The resins loaded with radioactive nuclides could not be regenerated and reused. These waste resins should be properly treated and disposed in order to minimize their potential hazard to the environments. In this paper, different technologies used for the treatment and disposal of spent radioactive resins were summarized and compared, including immobilization (such as cementation, bituminization and plastic solidification), advanced oxidation processes (such as incineration, pyrolysis, acid boiling degradation, the Fenton or Fenton-like reaction, supercritical water oxidation and plasma technology) and super compaction. Some supplementary methods, such as acid stripping, microbial conversion treatment and high integrity container were also mentioned. The principle of treatment methods, their characteristics and applications were briefly introduced, the future research directions were discussed.
Application Of Centrifugal Contactors In Partitioning Of High Level Waste In China

Wuhua Duan,Jianchen Wang,Jing Chen

2009-01-01

Abstract:High level waste (HLW) produced from reprocessing of the spent nuclear fuel still contains actinides, (90)Sr, (137)CS, (99)Tc, (129)I, etc., which engender permanent hazard to environment. The safe treatment and disposal of HLW are crucial to sustainable development of nuclear energy. The partitioning and transmutation (P&T) strategy for converting long-life nuclides from HLW into short-life radioactive or stable species has increasingly attracted interest. In recent years, a total partitioning process, including removal of actinides by the TRPO process, removal of Sr by the crown ether strontium extraction (CESE) process, removal of Cs by ion exchange using potassium titanium hexacyanoferrate (II) or by solvent extraction with 25,27-Bis(2-propyloxy) calix[4]-26,28-crown-6 (iPr-C[4]C-6), and separation of lanthanides and actinides with Cyanex 301, has been developed to treat Chinese HLW at Institute of Nuclear and New Energy Technology (INET), Tsinghua University, China. A series of cold and hot tests of both the separate processes and the total partitioning process were carried out with centrifugal contactors, and satisfactory results were obtained from these tests. In particular, a hot laboratory-scale test of the total partitioning process was carried out with the genuine HLW at INET in 1996. In this test, 50 stages phi 10 mm centrifugal contactors were applied successfully for removal of actinides and Sr. The test results showed that the decontamination factors (DFs) for total alpha activity, (99)Tc, (90)Sr and (137)Cs were 588, 125, >2500, and >200 respectively. In addition, a cold pilot-scale test of the total partitioning process was carried out with the simulated HLW at INET in 2005. In this test, 24 stages phi 70 mm centrifugal contactors were applied successfully in the stripping section of the TRPO process for removal of actinides. The test results showed that 99.9% of Nd, Zr and U was stripped respectively. In order to perform successfully these tests, a series of new centrifugal contactors have been developed at INET. In this paper, developments of centrifugal contactors for partitioning of HLW are introduced, and applications of centrifugal contactors in tests for partitioning of HLW in China are reviewed in detail.
Technology Selection for Emergency Radioactive Wastewater Treatment

Li Junfeng,Wang Jianlong

DOI: https://doi.org/10.4028/www.scientific.net/amr.724-725.708

2013-01-01

Advanced Materials Research

Abstract:Radioactive wastewater on accident cases is characterized by large quantity and complex quality, so the treatment process must be able to meet the request of large quantity, low energy consumption and mobile processing. The quantity and quality of radioactive wastewater under core melt accident case was estimated. The different characteristics of the radioactive waste treatment technology were compared. The practicable technologies and processes for emergency treatment of radioactive waste was analyzed. The recommended flow chart for emergency radioactive wastewater treatment was given out. Some suggestions were given for the research on the emergency treatment of radioactive wastewater technology.
Thermal plasma technology for radioactive waste treatment: a review

Eduardo S. P. Prado,Felipe S. Miranda,Leandro G. de Araujo,Gilberto Petraconi,Mauricio R. Baldan

DOI: https://doi.org/10.1007/s10967-020-07269-4

2020-07-08

Journal of Radioanalytical and Nuclear Chemistry

Abstract:In this paper, a review of radioactive wastes treatment using thermal plasma technology is presented as a treatment method for radioactive waste management.Virtually all waste streams can be treated by the thermal plasma technologies, resulting in a conditioned product, free from organics and liquids, definitely meeting the acceptance criteria for safe storage and disposal. The application of the thermal plasma system in the nuclear area is still one of the current research topics due to the theoretical and practical complexity of the treatment. This paper discusses the performance of the thermal plasma systems, addressing the advantages and limitations of the method.

chemistry, inorganic & nuclear, analytical,nuclear science & technology
Treatment of zeolite adsorbed material as a potential nuclear waste glass-ceramic matrix

Guilin Wei,Fen Luo,Yulong Miao,Wenhong Han,Yi Xie,Wenxiao Huang,Zhengfan Xu,Xirui Lu

DOI: https://doi.org/10.1111/jace.18094

IF: 4.186

2022-01-01

Journal of the American Ceramic Society

Abstract:Zeolite, as a common adsorption material, should be safely treated after adsorbing different nuclear wastes. In this study, different types of simulated zeolite wastes were successfully immobilized based on the exploring result of suitable experiment conditions. Firstly, sintering temperature was selected based on TG-DSC and phase results, which represented mainly as glassy phase. Then, the holding time was chosen through density and Vickers hardness results. For the sintering of zeolite, the suitable temperature is 1500celcius and the holding time is 1 h. Through the fitting process, FT-IR results demonstrate that the main microstructures compose of sheet silicates. Three types of simulated zeolite wastes can successfully transform into matrix and all the waste contents were uniformly immobilized. Finally, SEM-EDS results prove that the matrix is glass-ceramic which can well immobilize the considered nuclear wastes. This work proposes the idea of treatment of zeolite adsorbed material as a potential nuclear waste glass-ceramic matrix and the suitable conditions were also investigated.

Application of Cold Crucible Technique in the Nuclear Waste Treatment

Development and Advances in Cryogenic Treatment Technique and Device

Research and Development of Cold Crucible Melting and Casting Technology

Solidification of radioactive wastes by cement-based materials

Ceramics for high level radioactive waste solidification

Radioactive Wastewater Treatment Technologies: A Review

Extraction of Actinides and Lanthanides by Supercritical Fluid

Temperature Field during Melting and Solidification of Glass with Electromagnetic Cold Crucible

Research Progress in Cementation of Radioactive Wastes

Treatment of Cs-sorbed Zeolite As Spent Adsorbent by Cold Sintering for Stabilization and Solidification of Secondary Wastes

Application of melting technology in the treatment of nonferrous hazardous waste residues

Methods of Thermal Treatment of Radioactive Waste

Progress in Treatment Processes of Radioactive Wastewater from Nuclear Accident

Applications of Crushing and Grinding-Based Treatments for Typical Metal-Containing Solid Wastes: Detoxification and Resource Recovery Potentials.

Progress in Research on Cold Crucible Directional Solidification of Titanium Based Alloys

Treatment Method of Radioactive Waste Liquid Containing U and Cs

Treatment and disposal of spent radioactive ion-exchange resins produced in the nuclear industry

Application Of Centrifugal Contactors In Partitioning Of High Level Waste In China

Technology Selection for Emergency Radioactive Wastewater Treatment

Thermal plasma technology for radioactive waste treatment: a review

Treatment of zeolite adsorbed material as a potential nuclear waste glass-ceramic matrix