Abstract:The structure, morphology, and mechanical properties of two compression-molded grades of ultrahigh-molecular-weight polyethylene (UHMWPE) and, for comparison, one conventional linear polyethylene (HDPE) were studied. Compression molding resulted in some preferred orientation of lamellae in the compression direction in UHMWPE samples, while no preferred orientation in HDPE. The mean crystal thickness estimated from the size distribution agrees better with those obtained from small-angle X-ray scattering (SAXS) and mechanical yield data than the thickness determined from the melting peak temperature. Microscopic examination of microtomed and etched UHMWPE samples showed that the lamellae are in the form of platelets with the width and length in the range of 300-700 nm. The lamellae radiate from primary nuclei forming small embryonal spherulites; their radial growth ends at 0.3-0.7 μm from the center. There is no evidence of branching and secondary nucleation from those primary lamellae. Because the lamellae are radially ordered, there is no parallel stacking of lamellae. Samples were subjected to deformation by plane-strain compression at a constant true strain rate. In axial UHMWPE samples, where lamellae were preferentially oriented along the loading direction, the second yield was clearly observed. The second yield was found to be related to the deformation instability leading to kinking of lamellae oriented initially along the loading direction. Kinking was clearly shown by SAXS and microscopic observation of microtomed and etched samples. No cooperativity of kinking was observed because the lamellae are arranged in small spherulites and not parallel in stacks. The stress-strain curves were fitted with model curves assuming crystal plasticity and network elasticity in the amorphous component. The effective density of the molecular network within the amorphous phase depended on the molecular weight of UHMWPE.

Crystallization and Morphology of Ultra High Molar Mass Polyethylene from Dilute Solutions

Crystallization kinetics and crystalline structure of biodegradable Poly(ethylene adipate)

Studies on Nonisothermal Crystallization of Ultra–high Molecular Weight Polyethylene in Liquid Paraffin

Condensed State Of Pauci Or Multi-Chain Crystals Of Ultra High Molar Mass Polyethylene By Freeze-Drying

Melting Behavior and Morphology of Freeze-Dried Ultra-High Molar Mass Polyethylene

Preparation of Microporous Ultra High Molecular Weight Polyethylene (uhmwpe) by Thermally Induced Phase Separation of A Uhmwpe/Liquid Paraffin Mixture

Influence of intermolecular entanglements on crystallization behavior of ultra-high molar mass polyethylene

UHMWPE with Short‐chain Branches Synthesized by Alkenyl Substituted Phenoxy–imine Catalysts in Ethylene Polymerization

Studies On The Nature Of The Macromolecular Condensed State Of "Nascent" Ultra High Molar Mass Polyethylene

Effects of Different Ultrahigh Molecular Weight Polyethylene Contents on the Formation and Evolution of Hierarchical Crystal Structure of High‐density Polyethylene/ultrahigh Molecular Weight Polyethylene Blend Fibers

Molecular Dynamics Study of the Isothermal Crystallization Mechanism of Polyethylene Chain: the Combined Effects of Chain Length and Temperature

Morphologies of metallocene-catalyzed short chain branched polyethylene single crystals formed from the melt at higher temperature

Molecular Dynamics Simulation of Static Crystallization and Tensile Deformation of Bimodal HDPE/UHMWPE: Influence of Long Chain Content

Influence of Intermolecular Entanglements on Crystallization Behavior of Macromolecules

Lateral Habits of Single Crystals of Metallocene-Catalyzed Low Molecular Weight Short Chain Branched Polyethylene from the Melt

Melt Processing and Structural Manipulation of Highly Linear Disentangled Ultrahigh Molecular Weight Polyethylene

Effect of small amount of ultra high molecular weight component on the crystallization behaviors of bimodal high density polyethylene

Morphology and Plastic Yielding of Ultrahigh Molecular Weight Polyethylene

Effect of Crystallization Conditions on Melt Recrystallization Behavior of PE-UHMW

Effects of Addition of Ultra-High Molecular Weight Polyethylene on Tie-Molecule and Crystallization Behavior of Unimodal Pe-100 Pipe Materials

Structural evolution of ultra-high molecular weight polyethylene gel film stretching at different temperatures with reservation of shish crystals